參數資料
型號： MAX13041ASD/V+
廠商： Maxim Integrated Products
文件頁數： 3/20頁
文件大?。?/td> 0K
描述： IC CAN TXRX +/-80V HS 14SOIC
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 50
類型： 收發器
驅動器/接收器數： 1/1
規程： CAN
電源電壓： 4.75 V ~ 5.25 V
安裝類型： 表面貼裝
封裝/外殼： 14-SOIC（0.154"，3.90mm 寬）
供應商設備封裝： 14-SOIC
包裝： 管件
Detailed Description
The MAX13041 ±80V fault-protected, high-speed CAN
transceiver is intended for high-speed industrial and
automotive network applications where high reliability
and advanced power management are required. The
device links a CAN protocol controller to the physical
bus wires of the controller area network (CAN) and
allows communication at speeds up to 1Mbps. Built-in
level shifting allows for direct connection to protocol con-
trollers operating from lower voltages. The extended
fault-protected voltage range of ±80V on CAN bus lines
allows for use in +12V or +42V automotive, and higher
voltage +24V and +36V heavy-duty truck applications.
Advanced power management features make the
MAX13041 ideal for automotive electronic control unit
(ECU) modules that are permanently supplied by bat-
tery, regardless of the ignition switch position (clamp-
30, type-A modules). The device controls one or more
external voltage regulators to provide a low-power
sleep mode for an entire clamp-30 node. Wake-on CAN
capability allows the MAX13041 to restore power to the
node upon detection of CAN bus activity. The
MAX13041 is functionally compatible with the Philips
TJA1041A and is a pin-to-pin replacement with
improved performance.
CAN Interface
The ISO11898 specification describes the physical
layer of a controller area network (CAN). A CAN imple-
mentation is comprised of multiple transceiver modules
linked by a pair of bus wires. Communication between
modules occurs through transmission and reception of
differential logic states on the bus lines. Two compli-
mentary logic states are defined by ISO11898. A domi-
nant state results when the differential voltage on the
CAN bus lines is greater than 0.9V. A recessive bus
state results when the differential voltage is less than
0.5V (Figure 1). The CAN bus exhibits a wired-AND
characteristic, meaning the bus is only recessive when
all connected transmitters are recessive. Any transmit-
ter asserting a dominant logic state forces the entire
CAN bus dominant.
The MAX13041 accepts logic-level data from the CAN
protocol controller on TXD. Drive TXD low to assert a
dominant state on the CAN bus. Drive TXD high to
release the CAN bus to a recessive state. TXD is inter-
nally pulled up to VI/O. The state of the CAN bus is pre-
sented to the protocol controller as a logic level on
RXD. The MAX13041 receiver remains active during
transmission to allow for the bit-wise arbitration scheme
specified by the CAN protocol.
Level Shifting
The MAX13041 provides level shifting on TXD, RXD,
EN,
STB, WAKE and ERR for compatibility with lower-
voltage protocol controllers. Set the interface logic lev-
els for TXD, RXD, EN,
STB, WAKE, and ERR by
connecting VI/O to the supply voltage of a CAN protocol
controller, or another voltage from +2.8V to +5.25V.
Split-Termination and Common-Mode
Voltage Stabilization
The CAN bus specification requires a total bus load resis-
tance of 60Ω. Each end of the bus should be terminated
with 120Ω, the characteristic impedance of the bus line.
Electromagnetic emission (EME) is reduced by a split-ter-
mination method, whereby each end of the bus line is ter-
minated by 120Ω split into two 60Ω resistors in series
(see Figure 3). A bypass capacitor shunts noise to
ground from the node connecting the 60Ω resistors.
When the CAN bus is recessive, the common-mode
voltage is pulled low by the leakage current from inac-
tive modules. When the CAN bus subsequently goes
dominant, the proper common-mode voltage is
restored by the transmitting device. A common-mode
voltage step results, generating excessive EME. To mit-
igate this problem, the common-mode voltage of the
bus is forced to VCC/2 by biasing the split-termination
node (see Figure 3). During normal and PWON/listen-
only modes, a stabilized DC voltage of VCC/2 is present
on SPLIT. Connect SPLIT to the node connecting the
two 60Ω termination resistors to stabilize the common-
mode voltage of the bus and prevent EME from com-
mon-mode voltage steps.
Power-Management Operating Modes
The MAX13041 provides advanced power management
for a clamp-30 node by controlling one or more external
voltage regulators. Five operating modes provide differ-
ent functionality to minimize power consumption.
MAX13041
±80V Fault-Protected High-Speed CAN Transceiver
with Low-Power Management and Wake-On CAN
______________________________________________________________________________________
11
SPLIT
CANH
CANL
RT
60
Ω
CSPLIT
RT
60
Ω
Figure 3. Biased Split Termination
相關PDF資料
PDF描述
VI-25K-MX-F3 CONVERTER MOD DC/DC 40V 75W
MS27468T17B6P CONN RCPT 6POS JAM NUT W/PINS
78Q2133R/F TXRX 10/100 MDIX 3.3V IND 32-QFN
MAX3314ECKA+T IC TXRX RS232 460KBPS SOT23-8
VI-25K-MX-F1 CONVERTER MOD DC/DC 40V 75W
相關代理商/技術參數
參數描述
MAX13042EEBC+ 制造商:Maxim Integrated Products 功能描述:
MAX13042EEBC+T 功能描述:轉換 - 電壓電平 4Ch 100Mbps 3.2V RoHS:否 制造商:Micrel 類型:CML/LVDS/LVPECL to LVCMOS/LVTTL 傳播延遲時間:1.9 ns 電源電流:14 mA 電源電壓-最大:3.6 V 電源電壓-最小:3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MLF-8
MAX13042EETD+ 制造商:Maxim Integrated Products 功能描述:1.62V TO 3.6V IMPROVED HIGH-SPEED L - Rail/Tube
MAX13042EETD+T 功能描述:轉換 - 電壓電平 4Ch 100Mbps 3.2V RoHS:否 制造商:Micrel 類型:CML/LVDS/LVPECL to LVCMOS/LVTTL 傳播延遲時間:1.9 ns 電源電流:14 mA 電源電壓-最大:3.6 V 電源電壓-最小:3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MLF-8
MAX13042EEVKIT+ 功能描述:電源管理IC開發工具 MAX13042E Eval Kit RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*