- 您現在的位置：買賣IC網 > PDF目錄11710 > MAX13038ATI+ (Maxim Integrated Products)IC AUTO CONTACT MONITOR 28-TQFN PDF資料下載
參數資料
| 型號： | MAX13038ATI+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 7/22頁 |
| 文件大小： | 0K |
| 描述： | IC AUTO CONTACT MONITOR 28-TQFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 60 |
| 應用： | 自動 |
| 接口： | SPI |
| 電源電壓： | 6 V ~ 26 V |
| 封裝/外殼： | 28-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 28-TQFN-EP（5x5） |
| 包裝： | 管件 |
| 安裝類型： | 表面貼裝 |
MAX13037/MAX13038
Automotive Contact Monitor and
Level Shifters with LDO Regulator
______________________________________________________________________________________
15
Serial Peripheral Interface
(
CS, SD0, SDI, CLK)
The MAX13037/MAX13038 operate as a Serial Peripheral
Interface (SPI) slave devices. An SPI master accesses
the MAX13037/MAX13038 by reading from a status reg-
ister and writing to a command register. Both registers
are 16 bits long and are accessed most significant bit
(MSB) first.
On the falling edge of
CS, the status register is immedi-
ately loaded to an internal shift register and the con-
tents are transferred out of the SDO output on the rising
edge of CLK. Serial data on the SDI input is latched
into the shift register on the falling edge of CLK. On the
rising edge of
CS, the contents of the shift register are
copied to the command register (see Figure 7). The
status and command registers are 16 bits wide, so it is
essential to clock a total of 16 bits while
CS is low for
the input and output data to be valid. When
CS is high,
the SDO output is high-impedance and any transitions
on CLK and SDI are ignored. The
INT and OT flags are
cleared on the
CS falling edge. Input status changes
occurring during the
CS reading/writing operation are
allowed. If a switch status changes when
CS is low, the
interrupt is asserted as usual. This allows the part to be
used even if VLO is disabled provided that the INT out-
put is pulled up to another supply voltage.
Status Register
The status register contains the status of the switches
connected to IN7 through IN0 and it also contains an
overtemperature warning bit (see Table 1). The status
register is accessed through an SPI-compatible master.
Notes:
Bits 15–8: Switch 7 Through 0 Status (SW7–SW0)
SW7 through SW0 reflect the status of the switches
connected to inputs IN7 through IN0, respectively.
Open switches are returned as a [0] and closed switch-
es are returned as a [1].
Bit 7: Overtemperature Warning (OT)
The OT bit returns a [1] when the internal temperature of
the MAX13037/MAX13038 is above the temperature
warning threshold of +135°C (typ). The OT bit returns a
[0] when the MAX13037/MAX13038 is either below the
temperature threshold, or it has fallen below the tempera-
ture hysteresis level following an overtemperature event.
Bits 6–0: Unused
Bits 6 through 0 are unused and should be ignored.
Command Register
The command register is used to configure the
MAX13037/MAX13038 for various modes of operation
and is accessed by an SPI-compatible master (see
Table 2). The power-on reset (POR) value of the com-
mand register is 0x00.
CLK
* = UNUSED.
SDI
CS
SDO
15
STATUS REGISTER
IS COPIED TO
SHIFT REGISTER
SHIFT REGISTER IS
COPIED TO COMMAND
REGISTER
14
13
12
11
10
9876543210
WTOFF SC2
SC1
SC0
WEN WEND
M1
M0
P7
P6
P5
P4
P3
P2
P1
P0
SW7
SW6
SW5
SW4
SW3
SW2
SW1
SW0
OT
*
Figure 7. SPI Read/Write Example
Table 1. Status Register
BIT
15
1413
121110
9
8
7
6
5
4
3
2
1
0
NAME
SW7
SW6
SW5
SW4
SW3
SW2
SW1
SW0
OT
—
Table 2. Command Register
BIT
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
NAME
WTOFF
SC2
SC1
SC0
WEN
WEND
M1
M0
P7
P6
P5
P4
P3
P2
P1
P0
POR
0
00
000
00
相關PDF資料 |
PDF描述 |
|---|---|
| MAX7348AEP+T | IC KEY SWITCH 2WIRE 20-QSOP |
| C8051F834-GS | IC MCU 8BIT 4KB FLASH 16SOIC |
| VE-B7R-IW-F1 | CONVERTER MOD DC/DC 7.5V 100W |
| VE-B6X-IW-F3 | CONVERTER MOD DC/DC 5.2V 100W |
| C8051F823-GS | IC MCU 8BIT 8KB FLASH 16SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX13038ATI+ | 功能描述:接口 - 專用 Auto Contact Monitor & Level Shift w/LDO RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| MAX13038ATI+T | 制造商:Maxim Integrated Products 功能描述:AUTOMOTIVE CONTACT MONITOR AND LEVE - Tape and Reel |
| MAX13038ATX+ | 功能描述:接口 - 專用 Auto Contact Monitor & Level Shift w/LDO RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| MAX13038ATX+T | 功能描述:接口 - 專用 Auto Contact Monitor & Level Shift w/LDO RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| MAX1303AEUP | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。