- 您現在的位置：買賣IC網 > PDF目錄11710 > MAX13038ATI+ (Maxim Integrated Products)IC AUTO CONTACT MONITOR 28-TQFN PDF資料下載
參數資料
| 型號： | MAX13038ATI+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 6/22頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC AUTO CONTACT MONITOR 28-TQFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 60 |
| 應用： | 自動 |
| 接口： | SPI |
| 電源電壓： | 6 V ~ 26 V |
| 封裝/外殼： | 28-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 28-TQFN-EP（5x5） |
| 包裝： | 管件 |
| 安裝類型： | 表面貼裝 |
MAX13037/MAX13038
Automotive Contact Monitor and
Level Shifters with LDO Regulator
14
______________________________________________________________________________________
Wetting Current (WET)
The MAX13037/MAX13038 feature adjustable wetting
current to any closed switch to clean switch contacts
that are exposed to adverse conditions. The wetting
current is set by connecting a 30kΩ to 330kΩ resistor
from WET to ground. A 30kΩ resistor corresponds to a
wetting current of 40mA (typ) and a 330kΩ resistor cor-
responds to a 4mA (typ) wetting current. See the
Typical Operating Characteristics section for the rela-
tionship between the wetting current and RWET.
The WEN and WEND bits in the command register
enable and disable the wetting currents and the
WTOFF bit allows the wetting current to be activated for
a duration of 20ms (typ) (see the
Command Register
section). Disabling wetting currents, or limiting the
active wetting current time reduces power consump-
tion. The default state upon power-up is all wetting cur-
rents disabled.
Wetting current is activated on closed switches just
after the debounce time. The wetting current pulse
starts after the debounce time. A wetting current pulse
is provided to all closed switches when a valid input
change is detected. Wetting current rise and fall times
are controlled to enhance EMC performance. There is
one wetting current timer for all switch inputs.
Therefore, it is possible to observe wetting pulses
longer than expected whenever two switches turn on in
sequence and are spaced out less than tWET. In scan
mode, the wetting current is enabled during the polling
pulse only.
When using wetting currents, special care must be
taken to avoid exceeding the maximum power dissipa-
tion of the MAX13037/MAX13038 (see the
Applications
Information section).
Switch Outputs (DO0, DO1)
DO0 and DO1 are direct level-shifted outputs of the
switch inputs IN0 and IN1 when the WEND bit of the
command register is cleared and when operating in
normal mode. When configured as direct inputs, the
wetting currents and sensing resistors are disabled on
IN0 and IN1. DO0 and DO1 are three-stated when the
WEND bit is set or when operating in scan mode.
When programmed as direct inputs, the status of IN0
and IN1 are not reflected in the status register and
interrupts are not allowed on these inputs.
Interrupt Output (
INT)
INT is an active-low, open-drain output that asserts
when any of the switch inputs change state, as long as
the particular input is enabled for interrupts (set by
clearing P7–P0 in the command register).
INT also
asserts when the first watchdog timeout period elapses
(tWD1). A pullup resistor to VLO is needed on INT. INT is
cleared when
CS is driven low for a read/write operation.
The
INT output still asserts when VLO is disabled pro-
vided that it is pulled up to a different supply voltage.
Thermal Protection (
OT)
The MAX13037/MAX13038 feature a two-level thermal
protection strategy that prevents the device from being
damaged by overheating. At the initial warning temper-
ature of +135°C (typ), only wetting currents are dis-
abled. The MAX13037/MAX13038 return to normal
operation after the internal temperature decreases
below +120°C (typ). This protection feature is disabled
when WEN = 0 or when all inputs are open. At the sec-
ond thermal warning temperature of +170°C (typ), the
LDO is shut down. Because a C is often supplied by
the LDO, an overheating event caused by excessive
power dissipation related to I/O wetting currents is nor-
mally resolved without affecting the C status.
An open-drain, active-low output (
OT) asserts low when
the internal temperature of the device rises above the
thermal warning threshold.
OT is immediately cleared
when the
CS input is driven low for read/write opera-
tions, regardless of whether the temperature is above
the threshold, or not. The overtemperature status of the
MAX13037/MAX13038 can also be monitored by read-
ing the OT bit in the status register. The OT bit is set
when the internal temperature rises above the tempera-
ture threshold, and it is cleared when the temperature
falls below the temperature hysteresis level. This allows
a C to monitor the overtemperature status, even if the
OT output has been cleared. See Figure 6 for an exam-
ple timing diagram of the overtemperature alerts.
If desired, the
OT and INT outputs can be connected
to the same C GPIO in a wired-OR configuration to
save a C pin. The
OT output still asserts when VL is
absent provided that it is pulled up to a different sup-
ply voltage.
TEMPERATURE
OT
CS
OT BIT
Figure 6. Example Timing Diagram of the Overtemperature Alerts
相關PDF資料 |
PDF描述 |
|---|---|
| MAX7348AEP+T | IC KEY SWITCH 2WIRE 20-QSOP |
| C8051F834-GS | IC MCU 8BIT 4KB FLASH 16SOIC |
| VE-B7R-IW-F1 | CONVERTER MOD DC/DC 7.5V 100W |
| VE-B6X-IW-F3 | CONVERTER MOD DC/DC 5.2V 100W |
| C8051F823-GS | IC MCU 8BIT 8KB FLASH 16SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX13038ATI+ | 功能描述:接口 - 專用 Auto Contact Monitor & Level Shift w/LDO RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| MAX13038ATI+T | 制造商:Maxim Integrated Products 功能描述:AUTOMOTIVE CONTACT MONITOR AND LEVE - Tape and Reel |
| MAX13038ATX+ | 功能描述:接口 - 專用 Auto Contact Monitor & Level Shift w/LDO RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| MAX13038ATX+T | 功能描述:接口 - 專用 Auto Contact Monitor & Level Shift w/LDO RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| MAX1303AEUP | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。