- 您現在的位置：買賣IC網 > PDF目錄1935 > MAX13021ASA+ (Maxim Integrated Products)IC TRANSCEIVER LIN 8-SOIC PDF資料下載
參數資料
| 型號： | MAX13021ASA+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 2/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC TRANSCEIVER LIN 8-SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 100 |
| 類型： | 收發器 |
| 驅動器/接收器數： | 1/1 |
| 規程： | LIN |
| 電源電壓： | 5 V ~ 38 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SOIC |
| 包裝： | 管件 |
| 產品目錄頁面： | 1408 (CN2011-ZH PDF) |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
MAX13020/MAX13021
±60V Fault-Protected LIN Transceivers
10
Maxim Integrated
Sleep Mode
Sleep mode is the lowest power operating mode and is
the default state after power is applied to BAT. In sleep
mode, the MAX13020/MAX13021 disable the LIN trans-
mitter and receiver to reduce power consumption. RXD
and INH are high impedance. The internal slave termi-
nation resistor between LIN and BAT is disabled, and
only a weak pullup from LIN to BAT is enabled. While in
sleep mode, the MAX13020/MAX13021 transition to
standby mode when a local or remote wake-up event is
detected. For applications with a continuously powered
microprocessor, drive NSLP logic-high for longer than
tGOTONORM to force the MAX13020/MAX13021 directly
into normal slope mode if TXD is logic-high, and low
slope mode if TXD is logic-low. From normal slope or
low slope mode, drive NSLP logic-low for longer than
tGOTOSLEEP to force the MAX13020/MAX13021 into
sleep mode.
Standby Mode
In standby mode, the LIN transmitter and receiver are
disabled, the internal slave termination resistor between
LIN and BAT is enabled, and the INH output is pulled
high. The MAX13020/MAX13021 transition to standby
mode from sleep mode when a wake-up event is
detected. From standby mode, drive TXD logic-high or
logic-low, then drive NSLP logic-high for longer than
tGOTONORM to transition to normal slope or low slope
mode. In standby mode, RXD is driven logic-low to
transmit the wake-up interrupt flag to a microcontroller.
The wake-up source flag is presented on TXD as a
strong pulldown in the case of a local wake-up. In the
case of a remote wake-up, TXD is pulled low by the
internal 330k
resistor only. The wake-up interrupt and
wake-up source flag are cleared when the
MAX13020/MAX13021 transition to normal slope mode
or low slope mode.
Normal Slope Mode
In normal slope mode, the MAX13020/MAX13021 pro-
vide the physical layer interface to a LIN bus through
RXD and TXD. INH is pulled high and the internal slave
termination resistance from LIN to BAT is enabled. Data
presented on TXD is transmitted on the LIN bus with a
controlled slew rate to limit EME. Drive TXD logic-low to
assert a dominant state on LIN. The LIN bus state is
presented on the open-drain output RXD. A dominant
LIN state produces a logic-low on RXD. From standby
or sleep mode, drive TXD logic-high, then drive NSLP
logic-high for longer than tGOTONORM to enter normal
slope mode. Drive NSLP logic-low for longer than
tGOTOSLEEP to force the device into sleep mode from
normal slope mode.
NORMAL SLOPE MODE
FAULT MODE
LOW SLOPE MODE
SLEEP MODE
t(NSLP = 1 AFTER 0 TO 1)
> tGOTONORM
TXD = 1
t(LIN = DOMINANT)
> tLIN(DOM)(DET)
t(NSLP = 0 AFTER 1 TO 0)
> tGOTOSLEEP
t(NSLP = 0 AFTER 1 TO 0)
> tGOTOSLEEP
t(NSLP = 1 AFTER 0 TO 1)
> tGOTONORM
TXD = 0
INITIAL
POWER-ON STATE
STANDBY MODE
t(NSLP = 1 AFTER 0 TO 1)
> tGOTONORM
TXD = 1
t(NSLP = 1 AFTER 0 TO 1)
> tGOTONORM
TXD = 0
(tNWAKE = 0 AFTER 1 TO 0) > tNWAKE
OR
t(LIN = 0 AFTER 1 TO 0) >tBUS
t(LIN = RECESSIVE)
> tLIN(DOM)(REC)
DISABLE MODE
t(NWAKE = 0 AFTER 1 TO 0)
> tNWAKE
t(NSLP = 0 AFTER 1 TO 0)
> tGOTOSLEEP
t(NSLP = 1 AFTER 0 TO 1)
> tGOTONORM
t(LIN = DOMINANT)
> tLIN(DOM)(DET)
t(LIN = RECESSIVE)
> tLIN(DOM)(REC)
Figure 2. MAX13021 Operating Modes
相關PDF資料 |
PDF描述 |
|---|---|
| MAX13036ATI+T | IC CONTACT MONITOR AUTO 28-TQFN |
| MAX13037ATX+T | IC AUTO CONTACT MONITOR 36-TQFN |
| MAX13041ASD/V+T | IC CAN TXRX +/-80V HS 14SOIC |
| MAX13051ASA+ | IC TRANSCEIVER CAN 8-SOIC |
| MAX13054ASA+T | IC TRANSCEIVER CAN HS 8-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX13021ASA/V+ | 制造商:Maxim Integrated Products 功能描述:+/-60V FAULT-PROTECTED LIN TRANSCEIVER - Rail/Tube 制造商:Maxim Integrated Products 功能描述:IC TXRX LIN 60V FAULT PRO 8-SOIC 制造商:Maxim Integrated Products 功能描述:60V+/- Fault Prot LIN Transceiver |
| MAX13021ASA/V+T | 制造商:Maxim Integrated Products 功能描述:+/-60V FAULT-PROTECTED LIN TRANSCEIVER - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC TXRX LIN 60V FAULT PRO 8-SOIC 制造商:Maxim Integrated Products 功能描述:60V+/- Fault Prot LIN Transceiver |
| MAX13021ASA+ | 功能描述:LIN 收發器 60V Fault-Protect RoHS:否 制造商:NXP Semiconductors 工作電源電壓: 電源電流: 最大工作溫度: 封裝 / 箱體:SO-8 |
| MAX13021ASA+T | 功能描述:LIN 收發器 60V Fault-Protect RoHS:否 制造商:NXP Semiconductors 工作電源電壓: 電源電流: 最大工作溫度: 封裝 / 箱體:SO-8 |
| MAX1302AEUG+ | 功能描述:模數轉換器 - ADC 16Bit, 8Ch, 4.096V Multi-In Serial ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。