- 您現在的位置：買賣IC網 > PDF目錄1935 > MAX13021ASA+ (Maxim Integrated Products)IC TRANSCEIVER LIN 8-SOIC PDF資料下載
參數資料
| 型號： | MAX13021ASA+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 16/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC TRANSCEIVER LIN 8-SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 100 |
| 類型： | 收發器 |
| 驅動器/接收器數： | 1/1 |
| 規程： | LIN |
| 電源電壓： | 5 V ~ 38 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SOIC |
| 包裝： | 管件 |
| 產品目錄頁面： | 1408 (CN2011-ZH PDF) |
Detailed Description
The MAX13020/MAX13021 ±60V fault-protected low-
power local interconnect network (LIN) transceivers are
ideal for use in automotive network applications where
high reliability is required. The devices provide the
interface between the LIN master/slave protocol con-
troller and the physical bus described in the LIN 2.0
specification package and SAE J2602 specification.
The devices are intended for in-vehicle subnetworks
with a single master and multiple slaves.
The extended fault-protected voltage range of ±60V on
the LIN bus line allows for use in +12V, +24V, and
+42V automotive applications. The devices allow com-
munication up to 20kbaud, and include slew-rate limit-
ed transmitters for enhanced electromagnetic
emissions (EME) performance. The devices feature a
low-power 4A sleep mode and provide wake-up
source detection.
The MAX13020 is a pin-to-pin replacement and is func-
tionally compatible with the Philips TJA1020. The
MAX13021 includes enhanced bus dominant clamping
fault-management for reduced quiescent current during
LIN bus shorts to GND.
Operating Modes
The MAX13020/MAX13021 provide two different trans-
mitting modes, an intermediate standby mode and a
low-power sleep mode. Normal slope mode allows full-
speed communication at 20kbaud with a slew-limited
transmitter to reduce EME. Low slope mode permits
communication up to 10.4kbaud, and provides addi-
tional slew-rate limiting to further reduce EME. The
transmitting operating mode is selected by the logic
state of NSLP and TXD (Table 1). To enter normal slope
mode or low slope mode, drive TXD logic-high or logic-
low, then drive NSLP logic-high for longer than
tGOTONORM. The MAX13021 features two additional
operating modes to reduce current consumption during
LIN bus shorts to GND.
On initial power-up, the device enters sleep mode.
MAX13020/MAX13021
±60V Fault-Protected LIN Transceivers
9
Maxim Integrated
Pin Description
PIN
NAME
FUNCTION
1
RXD
Data Receive Output, Open Drain. RXD is logic-low when the LIN bus is dominant. RXD is active low after
a wake-up event from sleep mode.
2
NSLP
Sleep Input. Drive NSLP logic-high or logic-low to control the operating mode. (See Table 1 and Figures 1, 2)
3
NWAKE
Local Wake-Up Input. Present a falling edge on NWAKE to generate a local wake-up event. Connect
NWAKE to BAT with a 5k
resistor if local wake-up is not required.
4
TXD
Data Transmit Input, CMOS Compatible. Drive TXD logic-low to force the LIN bus to a dominant state in
normal/low slope mode.
5
GND
Ground
6
LIN
LIN Bus I/O. LIN is terminated with an internal 30k
resistor in normal slope, low slope, and standby
modes.
7
BAT
Battery Voltage Input. Bypass BAT to ground with a 0.1F ceramic capacitor as close to the device as
possible.
8
INH
Inhibit Output. INH is active high in standby and normal/low slope modes. (See Table 1)
NORMAL SLOPE MODE
STANDBY MODE
LOW SLOPE MODE
SLEEP MODE
t(NSLP = 1 AFTER 0 TO 1)
> tGOTONORM
TXD = 1
t(NSLP = 1 AFTER 0 TO 1)
> tGOTONORM
TXD = 1
t(NSLP = 1 AFTER 0 TO 1)
> tGOTONORM
TXD = 0
(tNWAKE = 0 AFTER 1 TO 0) > tNWAKE
OR
t(LIN = 0 AFTER 1 TO 0) >tBUS
t(NSLP = 0 AFTER 1 TO 0)
> tGOTOSLEEP
t(NSLP = 0 AFTER 1 TO 0)
> tGOTOSLEEP
t(NSLP = 1 AFTER 0 TO 1)
> tGOTONORM
TXD = 0
INITIAL
POWER-ON STATE
Figure 1. MAX13020 Operating Modes
相關PDF資料 |
PDF描述 |
|---|---|
| MAX13036ATI+T | IC CONTACT MONITOR AUTO 28-TQFN |
| MAX13037ATX+T | IC AUTO CONTACT MONITOR 36-TQFN |
| MAX13041ASD/V+T | IC CAN TXRX +/-80V HS 14SOIC |
| MAX13051ASA+ | IC TRANSCEIVER CAN 8-SOIC |
| MAX13054ASA+T | IC TRANSCEIVER CAN HS 8-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX13021ASA/V+ | 制造商:Maxim Integrated Products 功能描述:+/-60V FAULT-PROTECTED LIN TRANSCEIVER - Rail/Tube 制造商:Maxim Integrated Products 功能描述:IC TXRX LIN 60V FAULT PRO 8-SOIC 制造商:Maxim Integrated Products 功能描述:60V+/- Fault Prot LIN Transceiver |
| MAX13021ASA/V+T | 制造商:Maxim Integrated Products 功能描述:+/-60V FAULT-PROTECTED LIN TRANSCEIVER - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC TXRX LIN 60V FAULT PRO 8-SOIC 制造商:Maxim Integrated Products 功能描述:60V+/- Fault Prot LIN Transceiver |
| MAX13021ASA+ | 功能描述:LIN 收發器 60V Fault-Protect RoHS:否 制造商:NXP Semiconductors 工作電源電壓: 電源電流: 最大工作溫度: 封裝 / 箱體:SO-8 |
| MAX13021ASA+T | 功能描述:LIN 收發器 60V Fault-Protect RoHS:否 制造商:NXP Semiconductors 工作電源電壓: 電源電流: 最大工作溫度: 封裝 / 箱體:SO-8 |
| MAX1302AEUG+ | 功能描述:模數轉換器 - ADC 16Bit, 8Ch, 4.096V Multi-In Serial ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。