- 您現在的位置：買賣IC網 > PDF目錄2086 > MAX1301AEUP+ (Maxim Integrated Products)IC ADC 16BIT SRL 115KSPS 20TSSOP PDF資料下載
參數資料
| 型號： | MAX1301AEUP+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 17/31頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT SRL 115KSPS 20TSSOP |
| 產品培訓模塊： | Obsolescence Mitigation Program |
| 標準包裝： | 74 |
| 位數： | 16 |
| 采樣率（每秒）： | 115k |
| 數據接口： | MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 879mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 20-TSSOP |
| 包裝： | 管件 |
| 輸入數目和類型： | 4 個單端，單極；4 個單端，雙極；2 個差分，雙極 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
MAX1300/MAX1301
External Acquisition Mode (Mode 1)
The slowest maximum throughput rate is achieved with
the external acquisition method. SCLK controls the
acquisition of the analog signal in external acquisition
mode, facilitating precise control over when the analog
signal is captured. The internal clock controls the con-
version of the analog input voltage. The analog input
sampling instant is at the falling edge of the 16th SCLK
(Figure 3).
For the external acquisition mode, CS must remain low
for the first 15 clock cycles and the rise on or after the
falling edge of the 16th SCLK cycle as shown in Figure
3. For optimal performance, idle DIN and SCLK during
the conversion. With careful board layout, transitions at
DIN and SCLK during the conversion have a minimal
impact on the conversion result.
After the conversion is complete, SSTRB asserts high
and CS can be brought low to read the conversion
result. SSTRB returns low on the rising SCLK edge of
the subsequent start bit.
Internal Clock Mode (Mode 2)
In internal clock mode, the internal clock controls both
acquisition and conversion of the analog signal. The inter-
nal clock starts approximately 100ns to 400ns after the
falling edge of the eighth SCLK and has a rate of about
4.5MHz. The analog input sampling instant occurs at the
falling edge of the 11th internal clock signal (Figure 4).
For the internal clock mode, CS must remain low for the
first seven SCLK cycles and then rise on or after the
falling edge of the eighth SCLK cycle. After the conver-
sion is complete, SSTRB asserts high and CS can be
brought low to read the conversion result. SSTRB returns
low on the rising SCLK edge of the subsequent start bit.
Reset (Mode 4)
As shown in Table 8, set M[2:0] = 100 to reset the
MAX1300/MAX1301 to its default conditions. The default
conditions are full power operation with each channel
configured for ±3 x VREF, bipolar, single-ended conver-
sions using external clock mode (mode 0).
Partial Power-Down Mode (Mode 6)
As shown in Table 8, when M[2:0] = 110, the device
enters partial power-down mode. In partial power-
down, all analog portions of the device are powered
down except for the reference voltage generator and
bias supplies.
To exit partial power-down, change the mode by issu-
ing one of the following mode-control bytes (see the
Mode Control section):
External-Clock-Mode Control Byte
External-Acquisition-Mode Control Byte
Internal-Clock-Mode Control Byte
Reset Byte
Full Power-Down-Mode Control Byte
This prevents the MAX1300/MAX1301 from inadvertent-
ly exiting partial power-down mode because of a CS
glitch in a noisy digital environment.
Full Power-Down Mode (Mode 7)
When M[2:0] = 111, the device enters full power-down
mode and the total supply current falls to 1A (typ). In
full power-down, all analog portions of the device are
powered down. When using the internal reference,
upon exiting full power-down mode, allow 10ms for the
internal reference voltage to stabilize prior to initiating a
conversion.
To exit full power-down, change the mode by issuing
one of the following mode-control bytes (see the
Mode
Control section):
External-Clock-Mode Control Byte
8- and 4-Channel, ±3 x VREF Multirange Inputs,
Serial 16-Bit ADCs
24
______________________________________________________________________________________
M2
M1
M0
MODE
0
External Clock (DEFAULT)
0
1
External Acquisition
0
1
0
Internal Clock
0
1
Reserved
1
0
Reset
1
0
1
Reserved
1
0
Partial Power-Down
1
Full Power-Down
Table 8. Mode-Control Bits M[2:0]
相關PDF資料 |
PDF描述 |
|---|---|
| MAX13030EETE+ | IC LEVEL TRANS 6CH 16-TQFN-EP |
| MAX13043EETD+T | IC LEVEL TRANSLATOR 14-TDFN |
| MAX13047EEVB+ | IC XLATOR BIDIRECT LEVEL 10UTQFN |
| MAX13058EEWG+T | IC LEVEL TRANSLATOR 8CH 28-TQFN |
| MAX13101EETL+T | IC TRANSLATOR LL 16CH 40TQFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1301AEUP+ | 功能描述:模數轉換器 - ADC 16-Bit 4Ch 12V Serial ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1301AEUP+T | 功能描述:模數轉換器 - ADC 16-Bit 4Ch 12V Serial ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1301AEUP-T | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1301BEUP | 制造商:Maxim Integrated Products 功能描述:4-CHANNEL 12V MULTIRANGE INPUTS - Rail/Tube |
| MAX1301BEUP+ | 功能描述:模數轉換器 - ADC 16-Bit 4Ch 115ksps 4.136V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。