<form id="cqiy4"><meter id="cqiy4"></meter></form>
<code id="cqiy4"></code>
    <dd id="cqiy4"></dd>
    <code id="cqiy4"></code>
  • <menuitem id="cqiy4"><thead id="cqiy4"></thead></menuitem><table id="cqiy4"><nobr id="cqiy4"><optgroup id="cqiy4"></optgroup></nobr></table>
    <code id="cqiy4"></code>
  • <dd id="cqiy4"></dd>
    <dfn id="cqiy4"><pre id="cqiy4"><strong id="cqiy4"></strong></pre></dfn>
    參數資料
    型號: MAX1240AEPA+
    廠商: Maxim Integrated Products
    文件頁數: 2/15頁
    文件大小: 0K
    描述: IC ADC 12BIT SERIAL 8-DIP
    產品培訓模塊: Lead (SnPb) Finish for COTS
    Obsolescence Mitigation Program
    標準包裝: 50
    位數: 12
    采樣率(每秒): 73k
    數據接口: MICROWIRE?,QSPI?,串行,SPI?
    轉換器數目: 1
    功率耗散(最大): 727mW
    電壓電源: 單電源
    工作溫度: -40°C ~ 85°C
    安裝類型: 通孔
    封裝/外殼: 8-DIP(0.300",7.62mm)
    供應商設備封裝: 8-PDIP
    包裝: 管件
    輸入數目和類型: 1 個單端,單極
    MAX1240/MAX1241
    +2.7V, Low-Power,
    12-Bit Serial ADCs in 8-Pin SO
    10
    ______________________________________________________________________________________
    Using
    SHDN to Reduce Supply Current
    Power consumption can be reduced significantly by
    shutting down the MAX1240/MAX1241 between con-
    versions. Figure 6 shows a plot of average supply cur-
    rent versus conversion rate. Because the MAX1241
    uses an external reference voltage (assumed to be pre-
    sent continuously), it “wakes up” from shutdown more
    quickly (in 4s) and therefore provides lower average
    supply currents. The wake-up time (tWAKE) is the time
    from when SHDN is deasserted to the time when a con-
    version may be initiated (Figure 5). For the MAX1240,
    this time depends on the time in shutdown (Figure 7)
    because the external 4.7F reference bypass capacitor
    loses charge slowly during shutdown.
    External Clock
    The actual conversion does not require the external
    clock. This allows the conversion result to be read back
    at the P’s convenience at any clock rate from up to
    2.1MHz. The clock duty cycle is unrestricted if each
    clock phase is at least 200ns. Do not run the clock
    while a conversion is in progress.
    Timing and Control
    Conversion-start and data-read operations are controlled
    by the CS and SCLK digital inputs. The timing diagrams
    of Figures 8 and 9 outline serial-interface operation.
    A CS falling edge initiates a conversion sequence: the
    T/H stage holds the input voltage, the ADC begins to
    convert, and DOUT changes from high impedance to
    logic low. SCLK must be kept low during the conver-
    sion. An internal register stores the data when the con-
    version is in progress.
    10
    1
    0.01
    0.001
    0.1
    1
    10
    100
    1k
    10k
    100k
    0.1
    CONVERSION RATE (Hz)
    SUPPLY
    CURRNET
    (mA)
    VDD = VREF = 3.0V
    RLOAD =
    ∞, CLOAD = 50pF
    CODE = 010101010000
    MAX1241
    FIG.
    06a
    MAX1241
    MAX1240
    Figure 6. Average Supply Current vs. Conversion Rate
    1.0
    0.0
    0.001
    0.01
    0.1
    1
    10
    0.8
    0.6
    0.4
    0.2
    TIME IN SHUTDOWN (sec)
    POWER-UP
    DELAY
    (ms)
    MAX1240/41-07a
    Figure 7. Typical Reference Power-Up Delay vs. Time in
    Shutdown
    EOC
    INTERFACE IDLE
    CONVERSION
    IN PROGRESS
    EOC
    0
    μs
    TRAILING
    ZEROS
    IDLE
    CLOCK OUT SERIAL DATA
    TRACK/HOLD
    STATE
    TRACK
    HOLD
    TRACK
    DOUT
    B11 B10
    B9
    B8
    B7
    B6
    B5
    B4
    B3
    B2
    B1
    B0
    SCLK
    14
    8
    12
    16
    7.5
    μs (tCONV)
    HOLD
    0
    μs
    (tCS)
    TOTAL = 13.7
    μs
    12.5
    × 0.476μs = 5.95μs
    CYCLE TIME
    CS
    0.24
    μs
    Figure 8. Interface Timing Sequence
    相關PDF資料
    PDF描述
    MAX1245BCPP IC ADC SRL 12BIT 2.375V 20-DIP
    MAX1249AEPE+ IC ADC 10BIT SERIAL 16-DIP
    MAX1279AETC+ IC ADC 12BIT 1.5MSPS 12-TQFN
    MAX1285BESA+T IC ADC 12BIT 300KSPS 8-SOIC
    MAX1302BEUG+ IC ADC 16BIT SRL 115KSPS 24TSSOP
    相關代理商/技術參數
    參數描述
    MAX1240AEPA+ 功能描述:模數轉換器 - ADC 12-Bit 73ksps 3.6V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
    MAX1240AESA 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
    MAX1240AESA/V+ 功能描述:模數轉換器 - ADC 12-Bit 73ksps 3.6V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
    MAX1240AESA/V+T 功能描述:模數轉換器 - ADC 12-Bit 73ksps 3.6V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
    MAX1240AESA+ 功能描述:模數轉換器 - ADC 12-Bit 73ksps 3.6V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32