- 您現在的位置：買賣IC網 > PDF目錄384649 > MAX1211 (Maxim Integrated Products, Inc.) 40Msps, 12-Bit ADC PDF資料下載
參數資料
| 型號： | MAX1211 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | 40Msps, 12-Bit ADC |
| 中文描述： | 12位、65Msps、中頻采樣ADC |
| 文件頁數： | 23/29頁 |
| 文件大?。?/td> | 609K |
| 代理商： | MAX1211 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁
M
40Msps, 12-Bit ADC
______________________________________________________________________________________
23
The power-down mode allows the MAX1206 to efficient-
ly use power by transitioning to a low-power state when
conversions are not required. Additionally, the
MAX1206 parallel output bus goes high impedance in
power-down mode, allowing other devices on the bus
to be accessed.
In power-down mode, all internal circuits are off, the
analog supply current reduces to 0.045mA, and the
digital supply current reduces to 6μA. The following list
shows the state of the analog inputs and digital outputs
in power-down mode:
INP, INN analog inputs are disconnected from the
internal input amplifier (Figure 3).
REFOUT has approximately 17k
to GND.
REFP, COM, REFN go high impedance with respect
to V
DD
and GND, but there is an internal 4k
resis-
tor between REFP and COM, as well as an internal
4k
resistor between REFN and COM.
D0
–
D11, DOR, and DAV go high impedance.
CLKP, CLKN clock inputs go high impedance
(Figure 4).
The wake-up time from power-down mode is dominated
by the time required to charge the capacitors at REFP,
REFN, and COM. In internal reference mode and
buffered external reference mode, the wake-up time is
typically 10ms. When operating in the unbuffered exter-
nal reference mode, the wake-up time is dependent on
the external reference drivers.
Applications Information
Using Transformer Coupling
In general, the MAX1206 provides better SFDR and
THD with fully differential input signals than single-
ended input drive. In differential input mode, even-
order harmonics are lower as both inputs are balanced,
and each of the ADC inputs only requires half the signal
swing compared to single-ended input mode.
An RF transformer (Figure 9) provides an excellent
solution to convert a single-ended input source signal
to a fully differential signal, required by the MAX1206
for optimum performance. Connecting the center tap of
the transformer to COM provides a V
DD
/ 2 DC level
shift to the input. Although a 1:1 transformer is shown, a
step-up transformer can be selected to reduce the
drive requirements. A reduced signal swing from the
input driver, such as an op amp, can also improve the
overall distortion. The configuration of Figure 9 is good
for input frequencies up to Nyquist (f
CLK
/ 2).
The circuit of Figure 10 converts a single-ended input
signal to fully differential just as in Figure 9. However,
Figure 10 utilizes an additional transformer to improve
the common-mode rejection, allowing high-frequency
signals beyond the Nyquist frequency. The two sets of
49.9
termination resistors provide an equivalent 50
termination to the signal source. The second set of ter-
mination resistors connects to COM, providing the cor-
rect input common-mode voltage. Two 0
resistors in
series with the analog inputs allow high IF input fre-
quencies. These 0
resistors can be replaced with low-
value resistors to limit the input bandwidth.
Single-Ended AC-Coupled Input Signal
Figure 11 shows an AC-coupled, single-ended input
application. The MAX4108 provides high speed, high
bandwidth, low noise, and low distortion to maintain the
input signal integrity.
Buffered External Reference Drives
Multiple ADCs
The buffered external reference mode allows for more
control over the MAX1206 reference voltage and allows
multiple converters to use a common reference. The
REFIN input impedance is >50M
.
Figure 12 shows the MAX6062 precision bandgap ref-
erence used as a common reference for multiple con-
verters. The 2.048V output of the MAX6062 passes
through a one-pole 10Hz lowpass filter to the MAX4250.
The MAX4250 buffers the 2.048V reference before its
MAX1206
T1
N.C.
V
IN
6
1
5
2
4
3
12pF
12pF
0.1
μ
F
0.1
μ
F
2.2
μ
F
24.9
24.9
MINICIRCUITS
TT1-6
OR
T1-1T
INN
COM
INP
Figure 9. Transformer-Coupled Input Drive for Input
Frequencies Up to Nyquist
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1207 | 40Msps, 12-Bit ADC |
| MAX1208 | 40Msps, 12-Bit ADC |
| MAX1209 | 40Msps, 12-Bit ADC |
| MAX1206ETL | 40Msps, 12-Bit ADC |
| MAX1224CTC-T | 1.5Msps, Single-Supply, Low-Power, True-Differential, 12-Bit ADCs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1211ETL | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX1211ETL+ | 制造商:Maxim Integrated Products 功能描述:ADC SGL PIPELINED 65MSPS 12-BIT PARALLEL 40TQFN - Rail/Tube |
| MAX1211ETL+T | 制造商:Maxim Integrated Products 功能描述:ADC SGL PIPELINED 65MSPS 12-BIT PARALLEL 40TQFN - Tape and Reel |
| MAX1211ETL-T | 制造商:Maxim Integrated Products 功能描述:- Tape and Reel |
| MAX1211EVKIT | 制造商:Maxim Integrated Products 功能描述:EVALUATION KIT FOR THE MAX1211 MAX1206 MAX1207 MAX1208 MAX12 - Bulk |
發布緊急采購，3分鐘左右您將得到回復。