- 您現在的位置：買賣IC網 > PDF目錄2086 > MAX1169CEUD+T (Maxim Integrated Products)IC ADC 16BIT 58.6KSPS 14-TSSOP PDF資料下載
參數資料
| 型號： | MAX1169CEUD+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 6/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 16BIT 58.6KSPS 14-TSSOP |
| 標準包裝： | 2,500 |
| 位數： | 16 |
| 采樣率（每秒）： | 58.6k |
| 數據接口： | I²C，串行 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 864mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 14-TSSOP |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 8 個單端，單極 |
MAX1169
Acknowledge Bits
Successful data transfers are acknowledged with an
acknowledge bit (A) or a not-acknowledge bit (A). Both
the master and the MAX1169 (slave) generate acknowl-
edge bits. To generate an acknowledge, the receiving
device must pull SDA low before the rising edge of the
acknowledge-related clock pulse (ninth pulse) and
keep it low during the high period of the clock pulse
(Figure 8). To generate a not acknowledge, the receiver
allows SDA to be pulled high before the rising edge of
the acknowledge-related clock pulse and leaves it high
during the high period of the clock pulse.
Monitoring the acknowledge bits allows for detection of
unsuccessful data transfers. An unsuccessful data
transfer happens if a receiving device is busy or if a
system fault has occurred. In the event of an unsuc-
cessful data transfer, the master should reattempt com-
munication at a later time.
Slave Address
A master initiates communication with a slave device by
issuing a START condition followed by a slave address
byte. As shown in Figure 9, the slave address byte con-
sists of 7 address bits and a read/write bit (R/W). When
idle, the MAX1169 continuously waits for a START con-
dition followed by its slave address. When the
MAX1169 recognizes its slave address, it acquires the
analog input signal and prepares for conversion. The
first 3 bits (MSBs) of the slave address have been fac-
tory programmed and are always 011. Connecting
ADD3–ADD0 to DVDD or DGND, programs the last 4
bits (LSBs) of the slave address high or low.
Since the MAX1169 does not require setup or configu-
ration, the least significant bit (LSB) of the address byte
(R/W) controls power-down. In external reference mode
(REFADJ = AVDD), R/W is a don’t care. In internal refer-
ence mode, setting R/W = 1 places the device in nor-
mal operation and setting R/W = 0 powers down the
internal reference following the conversion (see the
Internal Reference Shutdown section).
After receiving the address, the MAX1169 (slave)
issues an acknowledge by pulling SDA low for one
clock cycle.
Bus Timing
At power-up, the MAX1169 bus timing defaults to fast
mode (F/S mode), allowing conversion rates up to
19ksps. The MAX1169 must operate in high-speed
mode (HS mode) to achieve conversion rates up to
58.6ksps. Figure 1 shows the bus timing for the
MAX1169 2-wire interface.
HS Mode
At power-up, the MAX1169 bus timing is set for F/S
mode. The master selects HS mode by addressing all
devices on the bus with the HS mode master code 0000
1XXX (X = don’t care). After successfully receiving the
HS mode master code, the MAX1169 issues a not
acknowledge, allowing SDA to be pulled high for one
clock cycle (Figure 10). After the not acknowledge, the
58.6ksps, 16-Bit, 2-Wire Serial ADC
in a 14-Pin TSSOP
14
______________________________________________________________________________________
Figure 8. Acknowledge Bits
12
8
9
ACKNOWLEDGE
NOT ACKNOWLEDGE
SCL
S
SDA
Figure 7. START and STOP Conditions
SP
Sr
SCL
SDA
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1177AEUP+ | IC ADC 16BIT 135KSPS 20-TSSOP |
| MAX117EPI+ | IC ADC 8BIT 400KSPS 28-DIP |
| MAX11800GTC/V+ | IC TOUCH SCREEN CTRLR LP 12WQFN |
| MAX11811GTP/V+ | IC TOUCH SCREEN CTRLR LP 20TQFN |
| MAX1181ECM+TD | IC ADC 10BIT 80MSPS DL 48-TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1169EVC16 | 功能描述:模數轉換器 - ADC MAX1169C16 EVAL KIT RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1169EVKIT | 功能描述:數據轉換 IC 開發工具 Evaluation System/Evaluation Kit for the MAX1169 RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| MAX1169EVSYS/EVKIT | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Evaluation System/Evaluation Kit for the MAX1169 |
| MAX1169N | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:58.6ksps, 16-Bit, 2-Wire Serial ADC in a 14-Pin TSSOP |
| MAX116CAX | 功能描述:數據轉換系統 RoHS:否 制造商:Texas Instruments 轉換速率:0.001 MSPs 分辨率:24 bit 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。