參數資料
型號： MAX11211EEE+T
廠商： Maxim Integrated Products
文件頁數： 10/27頁
文件大?。?/td> 0K
描述： ADC 18BIT DELTA-SIGMA 16-QSOP
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 2,500
位數： 18
數據接口： MICROWIRE?，QSPI?，串行，SPI?
轉換器數目： 1
功率耗散（最大）： 667mW
電壓電源： 模擬和數字
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 16-SSOP（0.154"，3.90mm 寬）
供應商設備封裝： 16-QSOP
包裝： 帶卷 (TR)
輸入數目和類型： *
18
Maxim Integrated
18-Bit, Single-Channel, Ultra-Low-Power, Delta-
Sigma ADCs with Programmable Gain and GPIO
MAX11209/MAX11211
STAT1: Status Register
SYSOR: The system gain overrange bit, when set to 1, indicates that a system gain calibration was over range. The
SCGC calibration coefficient is maximum value of 1.9999999. This bit, when set to 1, indicates that the full-scale value
out of the converter is likely not available.
RATE[2:0]: The data rate bits indicate the conversion rate that corresponds to the result in the DATA register or the
rate that was used for calibration coefficient calculation. If the previous conversions were done at a different rate, the
RATE[2:0] bits indicate a rate different than the rate of the conversion in progress.
OR: The overrange bit, OR, is set to 1 to indicate the conversion result has exceeded the maximum value of the
converter and that the result has been clipped or limited to the maximum value. The OR bit is set to 0 to indicate the
conversion result is within the full-scale range of the device.
UR: The underrange bit, UR, is set to 1 to indicate the conversion result has exceeded the minimum value of the
converter and that the result has been clipped or limited to the minimum value. The UR bit is set to 0 to indicate the
conversion result is within the full-scale range of the device.
MSTAT: The measurement status bit, MSTAT is set to 1 when a signal measurement is in progress. When MSTAT = 1,
a conversion, self-calibration, or system calibration is in progress and indicates that the modulator is busy. When the
modulator is not converting, the MSTAT bit is set to 0.
RDY: The RDY ready bit is set to 1 to indicate that a conversion result is available. Reading the DATA register resets the
RDY bit to 0 only after another conversion has been initiated. If the DATA has not been read before another conversion
is initiated, the RDY bit remains 1; if the DATA is read before another conversion is initiated, the RDY bit resets to 0. If
the DATA for the previous conversion is read during a following conversion, the RDY bit is reset immediately after the
DATA read operation has completed.
Table 11. STAT1 Register (Read Only)
BIT
B7
B6
B5
B4
B3
B2
B1
B0
BIT NAME
SYSOR
RATE2
RATE1
RATE0
OR
UR
MSTAT
RDY
DEFAULT
0
相關PDF資料
PDF描述
VE-21M-MX-F1 CONVERTER MOD DC/DC 10V 75W
IDT723663L15PF8 IC FIFO SYNC 4096X36 128QFP
MS27508E10F35SB CONN RCPT 13POS BOX MNT W/SCKT
IDT82V2048DA IC LIU T1/E1 8CH SHORT 144-TQFP
IDT72V3640L7-5BBI IC FIFO SS 1024X36 7-5NS 144BGA
相關代理商/技術參數
參數描述
MAX11212 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:18-Bit, Single-Channel, Ultra-Low Power, Delta-Sigma ADC with 2-Wire Serial Interface
MAX11212_12 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:18-Bit, Single-Channel, Ultra-Low Power, Delta-Sigma ADC with 2-Wire Serial Interface
MAX11212A 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:18-Bit, Single-Channel, Ultra-Low Power, Delta-Sigma ADC with 2-Wire Serial Interface
MAX11212AEUB 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:18-Bit, Single-Channel, Ultra-Low Power, Delta-Sigma ADC with 2-Wire Serial Interface
MAX11212AEUB+ 功能描述:模數轉換器 - ADC 18-Bit Delta-Sigma RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*