- 您現在的位置：買賣IC網 > PDF目錄17008 > MAX11200EVKIT+ (Maxim Integrated Products)KIT EVALUATION FOR MAX11200 PDF資料下載
參數資料
| 型號： | MAX11200EVKIT+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 11/27頁 |
| 文件大?。?/td> | 0K |
| 描述： | KIT EVALUATION FOR MAX11200 |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
19
Maxim Integrated
24-Bit, Single-Channel, Ultra-Low-Power,
Delta-Sigma ADCs with GPIO
MAX11200/MAX11210
CTRL1: Control 1 Register
The byte-wide CTRL1 register is a bidirectional read/write register. The byte written to the CTRL1 register indicates if
the part converts continuously or single cycle, if an external or internal clock is used, if the reference and signal buffers
are activated, the format of the data when in bipolar mode, and if the analog signal input range is unipolar or bipolar.
LINEF: Use the line frequency bit, LINEF, to select if the data rate is centered for 50Hz power mains or 60Hz power
mains. To select data rates for 50Hz power mains, write 1 to LINEF and to select data rates for 60Hz power mains,
write 0 to LINEF.
U/B: The unipolar/bipolar bit, U/B, selects if the input range is unipolar or bipolar. A 1 in this bit location selects a uni-
polar input range and a 0 selects a bipolar input range.
EXTCLK: The external clock bit, EXTCLK, controls the selection of the system clock. A 1 enables an external clock as
system clock, whereas as a 0 enables the internal clock.
REFBUF: The reference buffer bit, REFBUF, enables/disables the reference buffers. A 1 enables the reference buffers.
A 0 powers down the reference buffers and the reference inputs bypass the reference buffers when driving the ADC.
SIGBUF: The signal buffer, SIGBUF, enables/disables the signal buffers. A 1 enables the signal buffer. A 0 powers
down the signal buffers and the analog signal inputs bypass the signal buffers when driving the ADC.
FORMAT: The format bit, FORMAT, controls the digital format of the data. Unipolar data is always in offset binary for-
mat. The bipolar format is two’s complement if the FORMAT bit is set to 0 or offset binary if the FORMAT bit is set to 1.
SCYCLE: The single-cycle bit, SCYCLE, determines if the device runs in “no-latency” single-conversion mode
(SCYCLE = 1) or if the device runs in “l(fā)atent” continuous-conversion mode (SCYCLE = 0). When in single-cycle conver-
sion mode, the device completes one no-latency conversion and then powers down into a leakage-only state. When
in continuous-conversion mode, the part is continuously converting and the first three data from the part are incorrect
due to the SINC4 filter latency.
Important Note: When operating in continuous-conversion mode (SCYCLE = 0), it is recommended to keep CS low to
properly detect the end of conversion. The end of conversion is signaled by RDY/DOUT changing from 0 to 1. The tran-
sition of RDY/DOUT from 0 to 1 must be used to synchronize the DATA register read back. If the RDY/DOUT output is
not used to synchronize the DATA read back, a timing hazard exists where the DATA register is updated internally after
a conversion has completed simultaneously with the DATA register being read out, causing an incorrect read of DATA.
Table 12. CTRL1 Register (Read/Write)
BIT
B7
B6
B5
B4
B3
B2
B1
B0
BIT NAME
LINEF
U/B
EXTCLK
REFBUF
SIGBUF
FORMAT
SCYCLE
UNUSED
DEFAULT
0
1
0
相關PDF資料 |
PDF描述 |
|---|---|
| HCC06DRTF-S13 | CONN EDGECARD 12POS .100 EXTEND |
| HK1608R47J-T | INDUCTOR HI FREQ 470NH 5% 0603 |
| PCM16XD0 | PROCESSOR MODULE FOR MPLAB-ICE |
| SDR1006-681KL | INDUCTOR POWER 680UH 0.28A SMD |
| 0982660110 | CBL 10POS 0.5MM JMPR TYPE D 8" |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX11200EVKIT+ | 功能描述:數據轉換 IC 開發工具 MAX11200 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| MAX11201 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:24-Bit, Single-Channel, Ultra-Low-Power, Delta Sigma ADC with 2-Wire Serial Interface |
| MAX11201AEUB+ | 功能描述:模數轉換器 - ADC 24-Bit Delta-Sigma RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX11201AEUB+T | 功能描述:模數轉換器 - ADC 24-Bit Delta-Sigma RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX11201BEUB+ | 功能描述:模數轉換器 - ADC 24-Bit Delta-Sigma RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。