- 您現在的位置：買賣IC網 > PDF目錄17006 > MAX110EVC32-DIP (Maxim Integrated Products)EVAL KIT FOR MAX110 PDF資料下載
參數資料
| 型號： | MAX110EVC32-DIP |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 9/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVAL KIT FOR MAX110 |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| ADC 的數量： | 1 |
| 位數： | 14 |
| 采樣率（每秒）： | 50 |
| 數據接口： | 串行 |
| 輸入范圍： | ±VREF |
| 在以下條件下的電源（標準）： | 4.35mW @ 50SPS |
| 工作溫度： | 0°C ~ 70°C |
| 已用 IC / 零件： | MAX110，MAX111 |
| 已供物品： | 2 板，CD |
MAX110/MAX111
Low-Cost, 2-Channel, ±14-Bit Serial ADCs
______________________________________________________________________________________
17
3-Step Calibration
The data sheet electrical specifications apply to the
device after optional calibration of gain error and offset.
Uncalibrated, the gain error is typically 2%.
Table 3 describes the three steps required to calibrate
the ADC completely.
Once the ADC is calibrated to the selected channel, set
CAL = 0 and NUL = 0 and leave CHS unchanged in the
next control word to perform a signal conversion on the
selected analog input channel.
Calibrate the ADC after the following operations:
—
when power is first applied
—
if the reference common-mode voltage changes
—
if the common-mode voltage of the selected input
channel varies significantly. The CMRR of the analog
inputs is 0.25LSB/V.
—
after changing channels (if the common-mode volt-
ages of the two channels are different)
—
after changing conversion speed/resolution.
—
after significant changes in temperature. The offset
drift with temperature is typically 0.003V/°C.
Automatic gain calibration is not allowed in the
102,400 cycles per conversion mode (see
Programming Conversion Time). In this mode, calibra-
tion can be achieved by connecting the reference volt-
age to one input channel and performing a normal
conversion. Subsequent conversion results can be cor-
rected by software. Do not issue a N
NO
O--O
OP
P command
directly following the gain calibration, as the cali-
bration data will be lost.
Programming Conversion Time
The MAX110/MAX111 are specified for 12 bits of accu-
racy and up to ±14 bits of resolution. The ADC’s resolu-
tion depends on the number of clock cycles allowed
during each conversion. Control-register bits 9–12
(CONV1–CONV4) determine the conversion time by
controlling the nominal number of oversampling clock
cycles required for each conversion (OSCC/CONV).
Table 4 lists the available conversion times and result-
ing resolutions.
To program a new conversion time, perform a 3-step
calibration with the appropriate CONV1–CONV4 data
used in Table 3. The ADC is now calibrated at the new
conversion speed/resolution.
Table 4. Available Conversion Times
* Gain-calibration mode is not available with 102,400 clock cycles/conversion selected.
Clock duty cycles of 50% ±10% are recommended.
Table 5. Clock Divider-Ratio Control
CONV4 CONV3 CONV2 CONV1
CLOCK CYCLES
PER
CONVERSION
NOMINAL CONVERSION TIME
RCSEL = GND, DV2 = DV4 = 0, XCLK = 500kHz
(ms)
CONVERSION
RESOLUTION
(Bits)
1
0
1
10,240
20.48
12 + POL
0
1
20,480
40.96
13 + POL
0
1
0
81,920
163.84
14 + POL
0
102,400*
204.80
14 + POL
Not allowed
1
XCLK or internal RC oscillator is divided by 2 and connects to the ADC; fOSC = fXCLK
÷ 2.
0
1
XCLK or internal RC oscillator is divided by 4 and connects to the ADC; fOSC = fXCLK
÷ 4.
1
0
XCLK or internal RC oscillator connects directly to the ADC; fOSC = fXCLK.
0
DESCRIPTION
DV4
DV2
相關PDF資料 |
PDF描述 |
|---|---|
| 380LX153M016J022 | CAP ALUM 15000UF 16V 20% SNAP |
| SRR0603-221KL | INDUCTOR PWR 220UH 10% SHLD SMD |
| LGU2G221MELZ | CAP ALUM 220UF 400V 20% SNAP |
| MAX11040KEVKIT# | KIT EVAL FOR MAX11040 W/FMC CONN |
| 380LX221M200J202 | CAP ALUM 220UF 200V 20% SNAP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX110EVKIT | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Evaluation Kit for the MAX110/MAX111 |
| MAX110EVKIT-DIP | 功能描述:數據轉換 IC 開發工具 MAC110/1 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| MAX110EWE | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Analog-to-Digital Converter， 15-Bit |
| MAX110-MAX111 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Low-Cost, 2-Channel, 【14-Bit Serial ADCs |
| MAX110MJE | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Analog-to-Digital Converter， 15-Bit |
發布緊急采購，3分鐘左右您將得到回復。