參數資料
型號: MAX110EVC32-DIP
廠商: Maxim Integrated Products
文件頁數: 13/24頁
文件大?。?/td> 0K
描述: EVAL KIT FOR MAX110
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 1
ADC 的數量: 1
位數: 14
采樣率(每秒): 50
數據接口: 串行
輸入范圍: ±VREF
在以下條件下的電源(標準): 4.35mW @ 50SPS
工作溫度: 0°C ~ 70°C
已用 IC / 零件: MAX110,MAX111
已供物品: 2 板,CD
MAX110/MAX111
Low-Cost, 2-Channel, ±14-Bit Serial ADCs
20
______________________________________________________________________________________
Capacitive Loading Effects of XCLK in
Internal RC-Oscillator Mode
When using the internal RC oscillator, capacitive load-
ing effects on the XCLK pin must be minimized. Stray
capacitance causes the VDD power consumption to
increase by an amount p = 12CV2f, where C = stray
capacitance, V is the supply voltage, and f is the fre-
quency of the internal RC oscillator.
External Reference
The reference inputs to the ADC are high impedance,
allowing both an external voltage reference and ratio-
metric applications without loading effects. The fully dif-
ferential analog signal and reference inputs are
advantageous for performing ratiometric conversions
(Figures 11 and 12). For example, when measuring
load cells, the bridge excitation and the ADC reference
input both share the same voltage source. As the exci-
tation changes with temperature or voltage, the output
of the load cell will change. But since the differential
reference voltage also changes, the conversion results
remain constant, all else remaining equal.
Weigh Scale Application
The fully differential analog signal and reference inputs
make the MAX111 easy to interface to transducers with
differential outputs, such as the load cell in Figure 11.
Because the ADC input is differential, the load cell only
requires differential gain, eliminating the need for the
difference amplifier (differential to single-ended con-
verter) of the standard three op-amp instrumentation-
amplifier realization.
The 30mV full-scale bridge output is amplified to 2V
full-scale and applied to the MAX111 channel-one
input. The reference voltage to the ADC is created by a
voltage divider connected to the +5V rail. The same 5V
provides excitation for the bridge; therefore, as the
excitation voltage varies, the reference voltage to the
ADC also varies, providing an ADC output that does
not depend on the supply voltage.
The two 121k
resistors connected to the +5V supplies
shift the common-mode voltage from 2.5V (5V/2) to
1.5V to ensure linearity. Match these two resistors to
avoid introducing differential offset, or trim the resistor
mismatch with a potentiometer. In practice, the scale is
“zeroed” or “tared” by storing the average of several
conversions in a memory location while the scale is
+5V
30mV
FULL-SCALE
121k
2k
121k
49.9k
1k
22k
10k
1k
1/2 MAX492
1F
REF+
REF-
IN1+
IN1-
AGND
CS
DIN
DOUT
SCLK
49.9k
VDD
+5V
0.1F
MAX111
+5V
GND
Figure 11. Weigh Scale Application
相關PDF資料
PDF描述
380LX153M016J022 CAP ALUM 15000UF 16V 20% SNAP
SRR0603-221KL INDUCTOR PWR 220UH 10% SHLD SMD
LGU2G221MELZ CAP ALUM 220UF 400V 20% SNAP
MAX11040KEVKIT# KIT EVAL FOR MAX11040 W/FMC CONN
380LX221M200J202 CAP ALUM 220UF 200V 20% SNAP
相關代理商/技術參數
參數描述
MAX110EVKIT 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Evaluation Kit for the MAX110/MAX111
MAX110EVKIT-DIP 功能描述:數據轉換 IC 開發工具 MAC110/1 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V
MAX110EWE 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Analog-to-Digital Converter, 15-Bit
MAX110-MAX111 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Low-Cost, 2-Channel, 【14-Bit Serial ADCs
MAX110MJE 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Analog-to-Digital Converter, 15-Bit