- 您現在的位置：買賣IC網 > PDF目錄385520 > MAX110 (Maxim Integrated Products, Inc.) Low-Cost, 2-Channel, 4-Bit Serial ADCs(±5V，2通道，±14位串行模數轉換器) PDF資料下載
參數資料
| 型號： | MAX110 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | Low-Cost, 2-Channel, 4-Bit Serial ADCs(±5V，2通道，±14位串行模數轉換器) |
| 中文描述： | 低成本、2通道、±14位串行ADC |
| 文件頁數： | 11/24頁 |
| 文件大?。?/td> | 286K |
| 代理商： | MAX110 |
M
Low-Cost, 2-Channel, ±14-Bit S erial ADCs
______________________________________________________________________________________
11
ADC Operation
The output data from the MAX110/MAX111 is arranged
in twos-complement format (Figures 4, 5). The sign bit
(POL) is shifted out first, followed by the overrange bit
(OR), and the 14 data bits (MSB first) (see Figure 6).
The MAX110 operates from ±5V power supplies and
converts low-frequency analog signals in the ±3V
range when using the maximum reference voltage of
V
REF
= 3V (V
REF
= V
REF+
- V
REF-
). Within the ±3V input
range, greater accuracy is obtained within ±2.5V (see
Electrical Characteristics for details). Note that a nega-
tive input voltage is defined as V
IN-
> V
IN+
. For the
MAX110, the absolute voltage at any analog input pin
must remain within the (V
SS
+ 2.25V) to (V
DD
- 2.25V)
range.
The MAX111 operates from a single +5V supply and
converts low-frequency differential analog signals in the
±1.5V range when using the maximum reference volt-
age of V
REF
= 1.5V. As indicated in the Electrical
Characteristics greater accuracy is achieved within the
±1.2V range. The absolute voltage at any analog input
pin for the MAX111 must remain within 0V to V
DD
- 3.2V.
When V
IN-
> V
IN+
the input is interpreted as negative.
The overrange bit (OFL) is provided to sense when the
input voltage level has exceeded the reference voltage
level. The converter does not “saturate” until the input
voltage is typically 20% larger. The linearity is not guar-
anteed in this range. Note that the overrange bit works
properly if the reference voltage remains within the rec-
ommended voltage range (see Reference Inputs). If the
reference voltage exceeds the recommended input
range, the overrange bit may not operate properly.
Digital Interfac e—S tarting a Conversion
Data is transferred into and out of the serial I/O shift
register by pulling
CS
low and applying a serial clock
at SCLK. This fully static shift register allows SCLK to
range from DC to 2MHz. Output data from the ADC is
clocked out on SCLK’s falling edge and should be read
on SCLK’s rising edge. Input data to the ADC at DIN is
clocked in on SCLK’s rising edge. A new conversion
begins when
CS
returns high, provided the MSB in the
input control word (
NO-OP
) is a 1 (see Using the
MAX110/MAX111 with Microwire, SPI, and QSPI Serial
Interfaces). Figure 6 shows the detailed serial-interface
timing diagram.
CS
must remain high during the conversion
(while
BUSY
remains low). Bringing
CS
low during the conver-
sion causes the ADC to stop converting, and may
result in erroneous output data.
Using the MAX110/MAX111 with SPI, QSPI, and
Microwire Serial Interfaces
Figure 7 shows the most common serial-interface con-
nections. The MAX110/MAX111 are compatible with
SPI, QSPI (CPHA = 0, CPOL = 0), and Microwire serial-
interface standards.
XCLK
TTL/CMOS
RCSEL
GND
+5V
-5V (0V)
( ) ARE FOR MAX111.
V
DD
V
SS
(AGND)
MAX110
MAX111
Figure 3b. Connection for Internal RC-Oscillator Mode—XCLK
connects to the internal RC oscillator. Note, the pull-up resistor
is not necessary if the internal oscillator is never shut down.
XCLK
RCSEL
1M
GND
+5V
-5V (0V)
V
DD
+5V
V
SS
(AGND)
MAX110
MAX111
( ) ARE FOR MAX111.
Figure 3a. Connection for External-Clock Mode
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1126 | Quad, 12-Bit, 40Msps, 1.8V ADC with Serial LVDS Outputs |
| MAX1126EGK | Quad, 12-Bit, 40Msps, 1.8V ADC with Serial LVDS Outputs |
| MAX11504 | Four-Channel, Standard-Definition Video Filter |
| MAX11505 | Four-Channel, Standard-Definition Video Filter |
| MAX1168EVC16 | MAX1168 Evaluation Kit/Evaluation System |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX11008 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Dual RF LDMOS Bias Controller with Nonvolatile Memory |
| MAX11008BETM+ | 功能描述:射頻放大器 Dual RF LDMOS Bias Controller w/NV Mem RoHS:否 制造商:Skyworks Solutions, Inc. 類型:Low Noise Amplifier 工作頻率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 輸出截獲點:37.5 dBm 功率增益類型:32 dB 噪聲系數:0.85 dB 工作電源電壓:5 V 電源電流:125 mA 測試頻率:2.6 GHz 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 封裝:Reel |
| MAX11008BETM+T | 功能描述:射頻放大器 Dual RF LDMOS Bias Controller w/NV Mem RoHS:否 制造商:Skyworks Solutions, Inc. 類型:Low Noise Amplifier 工作頻率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 輸出截獲點:37.5 dBm 功率增益類型:32 dB 噪聲系數:0.85 dB 工作電源電壓:5 V 電源電流:125 mA 測試頻率:2.6 GHz 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 封裝:Reel |
| MAX11008EVC16 | 功能描述:放大器 IC 開發工具 MAX11008 Eval Kit RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V |
| MAX11008EVKIT+ | 功能描述:放大器 IC 開發工具 MAX11008 Eval Kit RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V |
發布緊急采購，3分鐘左右您將得到回復。