參數資料
型號: MAX11040KEVKIT#
廠商: Maxim Integrated Products
文件頁數: 25/35頁
文件大小: 0K
描述: KIT EVAL FOR MAX11040 W/FMC CONN
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
軟件下載: MAX11040KEVKIT
標準包裝: 1
ADC 的數量: 4
位數: 24
采樣率(每秒): 3.07M
數據接口: DSP,MICROWIRE?,QSPI?,串行,SPI?
輸入范圍: ±2.2 V
工作溫度: -40°C ~ 105°C
已用 IC / 零件: MAX11040K
已供物品: 板,線纜
MAX11040K/MAX11060
24-/16-Bit, 4-Channel, Simultaneous-Sampling,
Cascadable, Sigma-Delta ADCs
31
Maxim Integrated
DISCONTINUITY DUE TO SYNC EVENT
DRDYOUT
SYNC
MEASURE
tDRYOUT_TO_SYNC
AIN_
RECONSTRUCTED
DIGITAL OUTPUT
PAUSE FOR
tDRYOUT_TO_SYNC
NOTE: THE LATENCY IS NOT TO SCALE.
tDRYOUT_TO_SYNC
1
2
3
4
2
3
4
5
6
1
2
3
4
5
6
tS
Figure 19. Example of Discontinuity in Reconstructed Digital Output Due to SYNC Falling Edge with a Large DRDYOUT-to-SYNC Delay
Signal Distortion at
SYNC Falling Edges
Each SYNC falling edge causes a disruption in the digi-
tal filter timing proportional to the delay from the previ-
ous falling edge of DRDYOUT to the falling edge of
SYNC. Any analysis of the output data that assumes a
uniform sampling period sees an error proportional to
that delay, with a maximum value determined by the
maximum derivative of the analog input. Figure 19
shows the effect of this discontinuity at output sample 5.
Assuming a 60Hz ±2.2V sine wave, the maximum pos-
sible error on any given sample caused by a SYNC
falling edge is:
VERROR_MAX = 2.2V x 2π x 60Hz x tDRDYOUT_TO_SYNC
= 0.83μV/ns x tDRDYOUT_TO_SYNC
The delay from DRDYOUT to SYNC is quantized to
within one cycle of the 24.576MHz clock. SYNC pulses
that are asynchronous to DRDYOUT may cause large
errors. To eliminate this error, use a single clock source
for all devices and avoid disrupting the output data tim-
ing with SYNC pulses while making high-precision
measurements. Alternately, minimize the delay from
DRDYOUT to SYNC to minimize the error.
Example:
Assume fAIN_ = 60Hz, fS = 16ksps, and eight total
devices in the chain.
Device 1 has the longest tDRDYOUT_TO_SYNC delay,
therefore the worst-case SYNC error.
If device 1 has the fastest XIN clock in the chain, and
device 2 has the slowest XIN clock in the chain, and
they differ by 0.1%, device 1 completes its conversion
as much as 0.1% earlier than device 2. Hence, the
delay of device 2 is:
0.1% x (1/16kHz ) = 62.5ns
The signal then propagates down the chain at a time
delay of nominally 20ns for each device.
The total delay back to the SYNC falling edge after
going through six additional delays is:
tDELAY = 62.5ns + 6 x 20ns = 182.5ns
Maximum % Error = 2
π x fIN x tDRDYOUT_TO_SYNC x
100% = 2 x π x 60Hz x 182.5ns x 100% = 0.007%
The above error is relative to the signal level, not to the
full scale of the data converter.
相關PDF資料
PDF描述
380LX221M200J202 CAP ALUM 220UF 200V 20% SNAP
381LX471M200K012 CAP ALUM 470UF 200V 20% SNAP
GBC10DRES-S93 CONN EDGECARD 20POS .100 EYELET
MAX1110EVL11-DIP EVAL KIT FOR MAX1110
LGU2G151MELB CAP ALUM 150UF 400V 20% SNAP
相關代理商/技術參數
參數描述
MAX11040KEVKIT# 功能描述:數據轉換 IC 開發工具 MAX5135/11040/11612 Eval Kit w/ FMC RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V
MAX11040KGUU 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:24-/16-Bit, 4-Channel, Simultaneous-Sampling, Cascadable, Sigma-Delta ADCs
MAX11040KGUU/GG8 制造商:Maxim Integrated Products 功能描述:24-BIT, 4-CHANNEL, SIMULTANEOUS-SAMPLING, CASCADABLE, SIGMA- - Rail/Tube
MAX11040KGUU/GH9 制造商:Maxim Integrated Products 功能描述:24-BIT, 4-CHANNEL, SIMULTANEOUS-SAMPLING, CASCADABLE, SIGMA- - Rail/Tube
MAX11040KGUU+ 功能描述:模數轉換器 - ADC 24Bit 4Ch Simul-Samp Cascadable Sig Delt RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32