- 您現在的位置：買賣IC網 > PDF目錄383309 > MAX107 (Maxim Integrated Products, Inc.) Dual, 6-Bit, 400Msps ADC with On-Chip, Wideband Input Amplifier PDF資料下載
參數資料
| 型號： | MAX107 |
| 廠商： | Maxim Integrated Products, Inc. |
| 元件分類： | ADC |
| 英文描述： | Dual, 6-Bit, 400Msps ADC with On-Chip, Wideband Input Amplifier |
| 中文描述： | 雙路、6位、400Msps ADC，帶有片上寬帶輸入放大器 |
| 文件頁數： | 13/21頁 |
| 文件大?。?/td> | 1423K |
| 代理商： | MAX107 |
+1.2V, and must be differentially terminated at the far
end of each transmission line pair (true and comple-
mentary) with 100
.
Out-Of-Range Operation
A single output pair (DOR+, DOR-) is provided to flag
an out-of-range condition, if either the I or Q channel is
out-of-range, where out-of-range is above +FS or below
-FS. It features the same latency as the ADCs output
data and is demultiplexed in a similar fashion. With a
400MHz system clock, DOR+ and DOR- are clocked at
up to 200MHz.
Applications Information
Single-Ended Analog Inputs
The MAX107 is designed to work at full-speed for both
single-ended and differential analog inputs without sig-
nificant degradation in its dynamic performance. Both
input channels I (INI+, INI-) and Q (INQ+, INQ-) have
2k
impedance and allow for AC- and DC-coupled
input signals. In a typical DC-coupled single-ended
configuration (Table 1), the analog input signals enter
the analog input amplifier stages at the in-phase-input
pins INI+/INQ+, while the inverted phase input INI-
/INQ- pins are AC-coupled to AGNDI/AGNDQ. Single-
ended operation allows for an input amplitude of
800mVp-p, centered around V
REF
.
Differential Analog Inputs
To obtain +FS digital outputs with differential input drive
(Table 2), 400mV must be applied between INI+ (INQ+)
and INI- (INQ-). Midscale digital output codes occur
when there is no voltage difference between INI+
(INQ+) and INI- (INQ-). For a -FS digital output code
both in-phase (INI+, INQ+) and inverted input (INI-,
INQ-) must see -400mV.
Single-Ended to Differential
Conversion Using a Balun
An RF balun (Figure 3) provides an excellent solution to
convert a single-ended signal to a fully differential sig-
nal, required by the MAX107 for optimum performance.
At higher frequencies, the MAX107 provides better
SFDR and THD with fully differential input signals over
single-ended input signals. In differential input mode,
even-order harmonics are suppressed and each input
requires only half the signal-swing compared to single-
ended mode.
Clock Input
The MAX107 features clock inputs designed for either
single-ended or differential operation with very flexible
input drive requirements. The clock inputs (AC- or DC-
coupled) provide a 5k
input impedance to AV
CC
/2
and are internally buffered with a preamplifier to ensure
proper operation of the converter even with small-
amplitude sine-wave sources. The MAX107 was
M
Dual, 6-Bit, 400Msps ADC with On-Chip,
Wideband Input Amplifier
______________________________________________________________________________________
13
IN-PHASE INPUTS
(INI+, INQ+)
INVERTED INPUTS
(INI-, INQ-)
OUT-OF-RANGE BIT
(DOR+, DOR-)
OUTPUT CODE
> +400mV + V
REF
+400mV - 0.5LSB + V
REF
0V + V
REF
-400mV + 0.5LSB + V
REF
< -400mV + V
REF
AC-coupled to AGND_
AC-coupled to AGND_
AC-coupled to AGND_
AC-coupled to AGND_
AC-coupled to AGND_
1
0
0
0
1
011111
011111
000000/111111
100000
100000
Table 1. Digital Output Codes Corresponding to a DC-Coupled Single-Ended Analog
IN-PHASE INPUTS
(INI+, INQ+)
INVERTED INPUTS
(INI-, INQ-)
OUT-OF-RANGE BIT
(DOR+, DOR-)
OUTPUT CODE
>+200mV + V
REF
+200mV - 0.25LSB + V
REF
0V + V
REF
-200mV + 0.25LSB + V
REF
<-200mV + V
REF
<-200mV + V
REF
-200mV + 0.25LSB + V
REF
0V + V
REF
+200mV - 0.25LSB + V
REF
>+200mV + V
REF
1
0
0
0
1
011111
011111
000000/111111
100000
100000
Table 2. Digital Output Codes Corresponding to a DC-Coupled Differential Analog Input
相關PDF資料 |
PDF描述 |
|---|---|
| MAX107ECS | Dual, 6-Bit, 400Msps ADC with On-Chip, Wideband Input Amplifier |
| MAX1091BEEI | 250ksps, +3V, 8-/4-Channel, 10-Bit ADCs with +2.5V Reference and Parallel Interface |
| MAX1091ACEI | 250ksps, +3V, 8-/4-Channel, 10-Bit ADCs with +2.5V Reference and Parallel Interface |
| MAX1093ACEG | IGBT Module; Continuous Collector Current, Ic:400A; Collector Emitter Saturation Voltage, Vce(sat):2.4V; Power Dissipation, Pd:2800W; C-E Breakdown Voltage:1200V; Collector Current:400A; Collector Emitter Voltage, Vceo:3.4V RoHS Compliant: No |
| MAX1093AEEG | HARDWARE KIT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1070 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:1.5Msps, Single-Supply, Low-Power, True-Differential, 10-Bit ADCs |
| MAX1070_09 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:1.5Msps, Single-Supply, Low-Power, True-Differential, 10-Bit ADCs |
| MAX1070CTC | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1070CTC+ | 功能描述:模數轉換器 - ADC Integrated Circuits (ICs) RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1070CTC+T | 功能描述:模數轉換器 - ADC Integrated Circuits (ICs) RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。