- 您現在的位置：買賣IC網 > PDF目錄384647 > MAX106 (Maxim Integrated Products, Inc.) 【5V, 600Msps, 8-Bit ADC with On-Chip 2.2GHz Bandwidth Track/Hold Amplifier PDF資料下載
參數資料
| 型號： | MAX106 |
| 廠商： | Maxim Integrated Products, Inc. |
| 元件分類： | 運動控制電子 |
| 英文描述： | 【5V, 600Msps, 8-Bit ADC with On-Chip 2.2GHz Bandwidth Track/Hold Amplifier |
| 中文描述： | ±5V、600Msps、8位ADC，帶有片上2.2GHz帶寬采樣/保持放大器 |
| 文件頁數： | 14/32頁 |
| 文件大?。?/td> | 758K |
| 代理商： | MAX106 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
M
±5V, 600Msps, 8-Bit ADC with On-Chip
2.2GHz Bandwidth Track/Hold Amplifier
14
______________________________________________________________________________________
Internal Reference
The MAX106 features an on-chip +2.5V precision
bandgap reference that can be used by connecting
REFOUT to REFIN. This connects the reference output
to the positive input of the reference buffer. The buffer’s
negative input is internally tied to GNDR. GNDR must
be connected to GNDI on the user’s application board.
REFOUT can source up to 2.5mA to supply external
devices if required.
An adjustable external reference can be used to adjust
the ADC’s full-scale range. To use an external refer-
ence supply, connect a high-precision reference to the
REFIN pin and leave the REFOUT pin floating. In this
configuration, REFOUT
must not
be simultaneously
connected at any time, to avoid conflicts between the
two references. REFIN has a typical input resistance of
5k
and accepts input voltages of +2.5V ±200mV.
Using the MAX106’s internal reference is recommend-
ed for best performance.
Digital Outputs
The MAX106 provides data in offset binary format to dif-
ferential PECL outputs. A simplified circuit schematic of
the PECL output cell is shown in Figure 5. All PECL out-
puts are powered from V
CC
O, which may be operated
from any voltage between +3.0V to V
CC
D for flexible
interfacing with either +3.3V or +5V systems. The nomi-
nal V
CC
O supply voltage is +3.3V.
All PECL outputs on the MAX106 are open-emitter
types and must be terminated at the far end of each
transmission line with 50
to V
CC
O - 2V. Table 1 lists all
MAX106 PECL outputs and their functions.
Demultiplexer Operation
The MAX106 features an internal data demultiplexer,
which provides for three different modes of operation
(see the following sections on Demultiplexed DIV2
Mode, Non-Demultiplexed DIV1 Mode and Decimation
DIV4 Mode) controlled by two TTL/CMOS-compatible
inputs: DEMUXEN and DIVSELECT.
DEMUXEN enables or disables operation of the internal
1:2 demultiplexer. A logic high on DEMUXEN activates
the internal demultiplexer, and a logic low deactivates
it. With the internal demultiplexer enabled, DIVSELECT
controls the selection of the operational mode. DIVSE-
LECT low selects demultiplexed DIV2 mode, and DIV-
SELECT high selects decimation DIV4 mode (Table 2).
Auxiliary-Port Differential Outputs from LSB to MSB. A “+” indicates the true value; a “-”
denotes the complementary outputs.
A0+ to A7+,
A0- to A7-
Overrange True and Complementary Outputs
Reset Output True and Complementary Outputs
OR+, OR-
Data-Ready Clock True and Complementary Outputs. These signal lines are used to latch
the output data from the primary to the auxiliary output ports. Data changes on the rising
edge of the DREADY clock.
DREADY+, DREADY-
RSTOUT+, RSTOUT-
PECL OUTPUT SIGNALS
Primary-Port Differential Outputs from LSB to MSB. A “+” indicates the true value; a “-”
denotes the complementary outputs.
P0+ to P7+,
P0- to P7-
FUNCTION
DIFF.
PAIR
500
500
1.8mA
GNDD
GNDD
GNDD
V
CC
O
A_+/P_+
A_-/P_-
Figure 5. Simplified PECL Output Structure
Table 1. PECL Output Functions
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1071CTC-T | 1.5Msps, Single-Supply, Low-Power, True-Differential, 10-Bit ADCs |
| MAX1070CTC-T | 1.5Msps, Single-Supply, Low-Power, True-Differential, 10-Bit ADCs |
| MAX1070 | 1.5Msps, Single-Supply, Low-Power, True-Differential, 10-Bit ADCs |
| MAX1070ETC-T | 1.5Msps, Single-Supply, Low-Power, True-Differential, 10-Bit ADCs |
| MAX1071ETC-T | 1.5Msps, Single-Supply, Low-Power, True-Differential, 10-Bit ADCs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1060 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:400ksps, +5V, 8-/4-Channel, 10-Bit ADCs with +2.5V Reference and Parallel Interface |
| MAX1060ACEI | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1060ACEI+ | 功能描述:模數轉換器 - ADC 5V 10Bit 8Ch 400ksps w/2.5V Ref & Prl Int RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1060ACEI+T | 功能描述:模數轉換器 - ADC 5V 10Bit 8Ch 400ksps w/2.5V Ref & Prl Int RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。