- 您現在的位置：買賣IC網 > PDF目錄385520 > MAX1031ACEG-T (MAXIM INTEGRATED PRODUCTS INC) 10-Bit 300ksps ADCs with FIFO, Temp Sensor, Internal Reference PDF資料下載
參數資料
| 型號： | MAX1031ACEG-T |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | ADC |
| 英文描述： | 10-Bit 300ksps ADCs with FIFO, Temp Sensor, Internal Reference |
| 中文描述： | 16-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO24 |
| 封裝： | 0.150 INCH, 0.025 INCH PITCH, MO-137AE, QSOP-24 |
| 文件頁數： | 19/23頁 |
| 文件大?。?/td> | 254K |
| 代理商： | MAX1031ACEG-T |
M
10-Bit 300ksps ADCs with FIFO,
Temp Sensor, Internal Reference
______________________________________________________________________________________
19
clock. Scanning and averaging are disabled, and the
conversion result is available at DOUT during the con-
version. See Figure 7 for clock mode 11 timing.
Initiate a conversion by writing a byte to the conversion
register followed by 16 SCLK cycles. If
CS
is pulsed
high between the eighth and ninth cycles, the pulse
width must be less than 100μs. To continuously convert
at 16 cycles per conversion, alternate 1 byte of zeros
between each conversion byte.
If reference mode 00 is requested, or if an external ref-
erence is selected but a temperature measurement is
being requested, wait 65μs with
CS
high after writing
the conversion byte to extend the acquisition and allow
the internal reference to power up. To perform a tem-
perature measurement, write 24 bytes (192 cycles) of
zeros after the conversion byte. The temperature result
appears on DOUT during the last 2 bytes of the 192
cycles.
Partial Reads and Partial Writes
If the first byte of an entry in the FIFO is partially read
(
CS
is pulled high after fewer than 8 SCLK cycles), the
second byte of data that is read out contains the next 8
bits (not b7–b0). The remaining bits are lost for that
entry. If the first byte of an entry in the FIFO is read out
fully, but the second byte is read out partially, the rest
of the entry is lost. The remaining data in the FIFO is
uncorrupted and can be read out normally after taking
CS
low again, as long as the 4 leading bits (normally
zeros) are ignored. Internal registers that are written
partially through the SPI contain new values, starting at
the MSB up to the point that the partial write is stopped.
The part of the register that is not written contains previ-
ously written values. If
CS
is pulled low before
EOC
goes low, a conversion cannot be completed and the
FIFO is corrupted.
Transfer Function
Figure 8 shows the unipolar transfer function for single-
ended or differential inputs. Figure 9 shows the bipolar
transfer function for differential inputs. Code transitions
occur halfway between successive-integer LSB values.
Output coding is binary, with 1 LSB = V
REF
/ 1024V for
unipolar and bipolar operation, and 1 LSB = 0.125°C
for temperature measurements.
Layout, Grounding, and Bypassing
For best performance, use PC boards. Do not use wire-
wrap boards. For the TQFN package, connect its
exposed pad to GND. Board layout should ensure that
digital and analog signal lines are separated from each
other. Do not run analog and digital (especially clock)
signals parallel to one another or run digital lines under-
neath the MAX1027/MAX1029/MAX1031 package. High-
frequency noise in the V
DD
power supply can affect
performance. Bypass the V
DD
supply with a 0.1μF
capacitor to GND, close to the V
DD
pin. Minimize capac-
itor lead lengths for best supply-noise rejection. If the
power supply is very noisy, connect a 10
resistor in
series with the supply to improve power-supply filtering.
CS
DOUT
SCLK
DIN
EOC
MSB1
LSB1
MSB2
(ACQUISITION1)
(ACQUISITION2)
(CONVERSION1)
(CONVERSION BYTE)
EXTERNALLY TIMED ACQUISITION, SAMPLING AND CONVERSION WITHOUT CNVST.
X = DON'T CARE.
Figure 7. Clock Mode 11
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1031BCTI-T | 10-Bit 300ksps ADCs with FIFO, Temp Sensor, Internal Reference |
| MAX1031BETI-T | 10-Bit 300ksps ADCs with FIFO, Temp Sensor, Internal Reference |
| MAX104 | 【5V, 1Gsps, 8-Bit ADC with On-Chip 2.2GHz Track/Hold Amplifier |
| MAX104CHC | 【5V, 1Gsps, 8-Bit ADC with On-Chip 2.2GHz Track/Hold Amplifier |
| MAX105 | Dual, 6-Bit, 800Msps ADC with On-Chip, Wideband Input Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1031AEEG | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX1031AEEG-T | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:10-Bit 300ksps ADCs with FIFO,Temp Sensor, Internal Reference |
| MAX1031BCEG | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1031BCEG+ | 功能描述:模數轉換器 - ADC 10Bit 300ksps w/FIFO Temp Sensor Int Ref RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1031BCEG+T | 功能描述:模數轉換器 - ADC 10Bit 300ksps w/FIFO Temp Sensor Int Ref RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。