- 您現在的位置：買賣IC網 > PDF目錄385520 > MAX1031ACEG-T (MAXIM INTEGRATED PRODUCTS INC) 10-Bit 300ksps ADCs with FIFO, Temp Sensor, Internal Reference PDF資料下載
參數資料
| 型號： | MAX1031ACEG-T |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | ADC |
| 英文描述： | 10-Bit 300ksps ADCs with FIFO, Temp Sensor, Internal Reference |
| 中文描述： | 16-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO24 |
| 封裝： | 0.150 INCH, 0.025 INCH PITCH, MO-137AE, QSOP-24 |
| 文件頁數： | 12/23頁 |
| 文件大?。?/td> | 254K |
| 代理商： | MAX1031ACEG-T |
M
10-Bit 300ksps ADCs with FIFO,
Temp Sensor, Internal Reference
12
______________________________________________________________________________________
temperature measurement is performed before the first
temperature result is read out, the old measurement is
overwritten by the new result. Temperature results are
in degrees Celsius (two’s complement) at a resolution
of 1/8 of a degree. See the
Temperature Measurements
section for details on converting the digital code to a
temperature.
Internal Clock
The MAX1027/MAX1029/MAX1031 operate from an inter-
nal oscillator, which is accurate within 10% of the 4.4MHz
nominal clock rate. The internal oscillator is active in
clock modes 00, 01, and 10. Read out the data at clock
speeds up to 10MHz. See Figures 4–7 for details on tim-
ing specifications and starting a conversion.
Applications Information
Register Descriptions
The MAX1027/MAX1029/MAX1031 communicate
between the internal registers and the external circuitry
through the SPI/QSPI-compatible serial interface. Table
1 details the registers and the bit names. Tables 2–7
show the various functions within the conversion regis-
ter, setup register, averaging register, reset register,
unipolar register, and bipolar register.
Conversion Time Calculations
The conversion time for each scan is based on a num-
ber of different factors: conversion time per sample,
samples per result, results per scan, if a temperature
measurement is requested, and if the external refer-
ence is in use.
Use the following formula to calculate the total conver-
sion time for an internally timed conversion in clock
modes 00 and 10 (see the
Electrical Characteristics
section as applicable):
total conversion time = t
cnv
x n
avg
x n
result
+ t
TS
+ t
RP
where:
t
cnv
= t
acq
(max) + t
conv
(max)
n
avg
= samples per result (amount of averaging)
n
result
= number of FIFO results requested; determined
by number of channels being scanned or by NSCAN1,
NSCAN0
t
TS
= time required for temperature measurement; set
to zero if temp measurement is not requested
t
RP
= internal reference wake-up; set to zero if the inter-
nal reference is already powered up or if the external
reference is being used
In clock mode 01, the total conversion time depends on
how long
CNVST
is held low or high, including any time
required to turn on the internal reference. Conversion
time in externally clocked mode (CKSEL1, CKSEL0 = 11)
depends on the SCLK period and how long
CS
is held
high between each set of eight SCLK cycles.
Conversion Register
Select active analog input channels, scan modes, and
a single temperature measurement per scan by writing
to the conversion register. Table 2 details channel
selection, the four scan modes, and how to request a
temperature measurement. Request a scan by writing
to the conversion register when in clock mode 10 or 11,
or by applying a low pulse to the
CNVST
pin when in
clock mode 00 or 01.
A conversion is not performed if it is requested on a
channel that has been configured as
CNVST
or REF-.
Do not request conversions on channels 8–15 on the
MAX1027 and channels 12–15 on the MAX1029. Set
CHSEL3:CHSEL0 to the lower channel’s binary value. If
the last two channels are configured as a differential
REGISTER NAME
Conversion
Setup
Averaging
Reset
Unipolar Mode (Setup)
Bipolar Mode (Setup)
BIT 7
1
0
0
0
UCH0/1
BCH0/1
BIT 6
CHSEL3
1
0
0
UCH2/3
BCH1/2
BIT 5
CHSEL2
CKSEL1
1
0
UCH4/5
BCH4/5
BIT 4
CHSEL1
CKSEL0
AVGON
1
UCH6/7
BCH6/7
BIT 3
CHSEL0
REFSEL1
NAVG1
RESET
UCH8/9*
BCH8/9*
BIT 2
SCAN1
REFSEL0
NAVG0
X
UCH10/11* UCH12/13** UCH14/15**
BCH10/11* BCH12/13** BCH14/15**
BIT 1
SCAN0
DIFFSEL1
NSCAN1
X
BIT 0
TEMP
DIFFSEL0
NSCAN0
X
Table 1. Input Data Byte (MSB First)
*
Unipolar/bipolar channels 8–15 are only valid on the MAX1029 and MAX1031.
**
Unipolar/bipolar channels 12–15 are only valid on the MAX1031.
X = Don’t care.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1031BCTI-T | 10-Bit 300ksps ADCs with FIFO, Temp Sensor, Internal Reference |
| MAX1031BETI-T | 10-Bit 300ksps ADCs with FIFO, Temp Sensor, Internal Reference |
| MAX104 | 【5V, 1Gsps, 8-Bit ADC with On-Chip 2.2GHz Track/Hold Amplifier |
| MAX104CHC | 【5V, 1Gsps, 8-Bit ADC with On-Chip 2.2GHz Track/Hold Amplifier |
| MAX105 | Dual, 6-Bit, 800Msps ADC with On-Chip, Wideband Input Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1031AEEG | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX1031AEEG-T | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:10-Bit 300ksps ADCs with FIFO,Temp Sensor, Internal Reference |
| MAX1031BCEG | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1031BCEG+ | 功能描述:模數轉換器 - ADC 10Bit 300ksps w/FIFO Temp Sensor Int Ref RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1031BCEG+T | 功能描述:模數轉換器 - ADC 10Bit 300ksps w/FIFO Temp Sensor Int Ref RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。