- 您現在的位置：買賣IC網 > PDF目錄1935 > MAX1021BETX+ (Maxim Integrated Products)IC ADC/DAC 10BIT W/FIFO 36-TQFN PDF資料下載
參數資料
| 型號： | MAX1021BETX+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 14/40頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC/DAC 10BIT W/FIFO 36-TQFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 50 |
| 類型： | ADC，DAC |
| 分辨率（位）： | 10 b |
| 采樣率（每秒）： | 300k |
| 數據接口： | 串行 |
| 電壓電源： | 模擬和數字 |
| 電源電壓： | 2.7V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 36-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 36-TQFN 裸露焊盤（6x6） |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
MAX1021/MAX1043
10-Bit, Multichannel ADCs/DACs with FIFO,
Temperature Sensing, and GPIO Ports
______________________________________________________________________________________
21
Write to the GPIOs by writing a command byte to the
GPIO command register. Write a single data byte to the
MAX1021/MAX1043 following the command byte.
The GPIOs can sink and source current. GPIOA0 and
GPIOA1 can sink and source up to 15mA. GPIOC0 and
GPIOC1 can sink 4mA and source 2mA. See Table 3.
Clock Modes
Internal Clock
The MAX1021/MAX1043 can operate from an internal
oscillator. The internal oscillator is active in clock
modes 00, 01, and 10. Figures 6, 7, and 8 show how to
start an ADC conversion in the three internally timed
conversion modes.
Read out the data at clock speeds up to 25MHz
through the SPI interface.
External Clock
Set CKSEL1 and CKSEL0 in the setup register to 11 to
set up the interface for external clock mode 11. See
Table 5. Pulse SCLK at speeds from 0.1MHz to
3.6MHz. Write to SCLK with a 40% to 60% duty cycle.
The SCLK frequency controls the conversion timing.
See Figure 9 for clock mode 11 timing. See the
ADC
Conversions in Clock Mode 11 section.
ADC/DAC References
Address the reference through the setup register, bits 3
and 2. See Table 5. Following a wake-up delay, set
REFSEL[1:0] = 00 to program both the ADC and DAC
for internal reference use. Set REFSEL[1:0] = 10 to pro-
gram the ADC for internal reference. Set REFSEL[1:0] =
10 to program the DAC for external reference, REF1.
When using REF1 or REF2/AIN_ in external-reference
mode, connect a 0.1F capacitor to AGND. Set
REFSEL[1:0] = 01 to program the ADC and DAC for
external-reference mode. The DAC uses REF1 as its
external reference, while the ADC uses REF2 as its
external reference. Set REFSEL[1:0] = 11 to program
the ADC for external differential-reference mode. REF1
is the positive reference and REF2 is the negative refer-
ence in the ADC external differential mode.
When REFSEL[1:0] = 00 or 10, REF2/AIN_ functions as
an analog input channel. When REFSEL[1:0] = 01 or 11,
REF2/AIN_ functions as the device’s negative reference.
Temperature Measurements
Issue a command byte setting bit 0 of the conversion
register to one to take a temperature measurement.
See Table 4. The MAX1021/MAX1043 perform tempera-
ture measurements with an internal diode-connected
transistor. The diode bias current changes from 68A to
4A to produce a temperature-dependent bias voltage
difference. The second conversion result at 4A is sub-
tracted from the first at 68A to calculate a digital value
that is proportional to absolute temperature. The output
data appearing at DOUT is the digital code above,
minus an offset to adjust from Kelvin to Celsius.
The reference voltage used for the temperature mea-
surements is always derived from the internal reference
source to ensure that 1 LSB corresponds to 1/8th of a
degree Celsius. On every scan where a temperature
measurement is requested, the 12-bit temperature con-
version is carried out first. The first 2 bytes of data read
from the FIFO contain the result of the 12-bit tempera-
ture measurement. If another temperature measure-
ment is performed before the first temperature result is
read out, the old measurement is overwritten by the
new result. Temperature results are in degrees Celsius
(two’s complement). See the
Applications Information
section for information on how to perform temperature
measurements in each clock mode.
Register Descriptions
The MAX1021/MAX1043 communicate between the
internal registers and the external circuitry through the
SPI-compatible serial interface. Table 1 details the
command byte, the registers, and the bit names.
Tables 4–12 show the various functions within the con-
version register, setup register, unipolar-mode register,
bipolar-mode register, ADC averaging register, DAC
select register, reset register, and GPIO command reg-
ister, respectively.
Conversion Register
Select active analog input channels, scan modes, and
a single temperature measurement per scan by issuing
a command byte to the conversion register. Table 4
details channel selection, the four scan modes, and
how to request a temperature measurement. Start a
scan by writing to the conversion register when in clock
mode 10 or 11, or by applying a low pulse to the
CNVST pin when in clock mode 00 or 01. See Figures 6
and 7 for timing specifications for starting a scan with
CNVST.
CURRENT
GPIOA0, GPIOA1
(mA)
GPIOC0, GPIOC1
(mA)
Sink
15
4
Source
15
2
Table 3. GPIO Maximum Sink/Source
Current
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1042BETX+ | IC ADC/DAC 10BIT W/FIFO 36TQFN |
| MAX1057BETM+T | IC ADC/DAC 10BIT 48-TQFN-EP |
| MAX11041ETC+T | IC REMOTE CTRLR WIRED 12-TQFN |
| MAX11043ATL+T | IC ADC 16BIT W/DAC 40-TQFN-EP |
| MAX11359AETL+T | IC DAS SYSTEM 16BIT 40-TQFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1021BETX+ | 功能描述:ADC / DAC多通道 10Bit AD/DACs w/FIFO Temp Sns/GPIO Ports RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40 |
| MAX1021BETX+T | 功能描述:ADC / DAC多通道 10Bit AD/DACs w/FIFO Temp Sns/GPIO Ports RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40 |
| MAX1021BETX-T | 功能描述:ADC / DAC多通道 RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40 |
| MAX1022 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:10-Bit, Multichannel ADCs/DACs with FIFO, Temperature Sensing, and GPIO Ports |
| MAX1022BETX | 功能描述:ADC / DAC多通道 RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40 |
發布緊急采購，3分鐘左右您將得到回復。