
M
Mobile-Radio Analog Controller
2
_______________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS
AV
DD
or DV
DD
to AGND or DGND...........................-0.3V to +6V
Digital Inputs to DGND.............................................-0.3V to +6V
Analog Inputs to AGND............................................-0.3V to +6V
REF to AGND............................................................-0.3V to +6V
AGND to DGND.................................................................± 0.3V
AV
DD
to DV
DD
....................................................................± 0.3V
Maximum Current into Any Pin............................................50mA
ELECTRICAL CHARACTERISTICS
(AV
DD
= DV
DD
= +2.85V to +3.6V, f
SCLK
= 1.152MHz, T
A
= T
MIN
to T
MAX
, unless otherwise noted.)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
Continuous Power Dissipation (T
A
= +70°C)
SSOP (derate 8.0mW/°C above +70°C) ......................640mW
Operating Temperature Ranges
MAX1007CAG.....................................................0°C to +70°C
MAX1007EAG..................................................-40°C to +85°C
Storage Temperature Range.............................-65°C to +150°C
Lead Temperature (soldering, 10sec) .............................+300°C
AV
DD
, DV
DD
RxEN = 1, TxEN = 1; AV
DD
= DV
DD
= 3V
RxEN = 1, TxEN = 0; AV
DD
= DV
DD
= 3V; PKWDW and
ADCCTRL as per state B on Figure 1
RxEN = 1, TxEN = 0; AV
DD
= DV
DD
= 3V;
PKWDW = ADCCTRL = DGND
RxEN = 1, TxEN = 0; AV
DD
= DV
DD
= 3V; PKWDW and
ADCCTRL as per state B on Figure 1. PSDWDW and PSD-
CNTRL as per state D on Figure 2
RxEN = 0, TxEN = 1; AV
DD
= DV
DD
= 3V;
PKWDW = ADCCTRL = DGND
RxEN = 0, TxEN = 1; AV
DD
= DV
DD
= 3V;
PKWDW and ADCCTRL as per state B on Figure 1
RxEN = 1, TxEN = 0; AV
DD
= DV
DD
= 3V; PKWDW and
ADCCTRL as per state C on Figure 1
RxEN = 0, TxEN = 1; AV
DD
= DV
DD
= 3V;
PKWDW and ADCCTRL as per state C on Figure 1
CONDITIONS
mA
1.24
3.5
Standby:
XDAC, GDAC, Ref, RefBuf Active
mA
4.07
10.5
Receive Mode 4:
KDAC, XDAC, ADC, RSSI
Buffer, Ref, RefBuf, PSD
Circuit Active
mA
11.2
31
Receive Mode 3:
KDAC, XDAC, ADC, Peak
Detector RSSI Buffer, Ref,
RefBuf Active
V
2.85
3.0
3.6
Supply Voltages
SUPPLY CURRENTS
[I(AV
DD
) + I(DV
DD
)] (Note 1)
mA
2.95
Receive Mode 2:
KDAC, XDAC, Peak Detector,
RSSI Buffer, Ref, RefBuf Active
mA
1.24
3.5
Receive Mode 1:
KDAC, XDAC, Ref, RefBuf
Active
mA
1.8
5.0
Transmit Mode 1:
All DACs, Ref, RefBuf Active
mA
4.7
Transmit Mode 2:
All DACs, PGA, REF, Peak
Detector, PSBIAS, I
SOURCE
,
RefBuf Active
Transmit Mode 3:
All DACs, PGA, REF, Peak
Detector, PSBIAS, I
SOURCE
,
RefBuf, ADC Active
mA
12.2
32
UNITS
MIN
TYP
MAX
PARAMETER
RxEN = 0, TxEN = 0; AV
DD
= DV
DD
= 3V;
ADCCTRL = PSDCTRL = PKWDW = PSDWDW = DGND;
SCLK not active, either high or low
μA
1
10
Total Shutdown
POWER-SUPPLY REQUIREMENTS