- 您現在的位置：買賣IC網 > PDF目錄370965 > M52756SP (Mitsubishi Electric Corporation) WIDE BAND ANALOG SWITCH PDF資料下載
參數資料
| 型號： | M52756SP |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | WIDE BAND ANALOG SWITCH |
| 中文描述： | 寬頻帶模擬開關 |
| 文件頁數： | 15/19頁 |
| 文件大小： | 585K |
| 代理商： | M52756SP |
M52756SP
WIDE BAND ANALOG SWITCH
MITSUBISHI ICs (Monitor)
ELECTRIC
(
/ 19 )
MITSUBISHI
50%
Trd
Tfd
50%
SG7
Output waveform
note17, note18) The condition is as table 1. Set SW15 to GND (OPEN), SG7 is as the input signal of
input terminal, measure the waveform of output. Rising delay time is as Trd1 (Trd2).
Falling delay time is as Tfd1(Tfd2). Reference to the Fig. as shown below.
note19) 1. The condition is as table 1. SG1 is as the input signal of Pin1, Pin3, Pin5, and SG7 is as the
input signal of Pin6, Pin7. There is no input at another pins.
2. Input 0V at Pin15, confirm that there are signals output from T.P.29, T.P.26, T.P.23, T.P.21,
T.P.18,T.P.17.
3. Increasing gradually the voltage of terminal Pin15. Read the voltage when there is no signal
output from the terminals listed as above. The voltage is as Vsth1.
4. SG1 as the input signal of Pin8, Pin10, Pin12, and SG7 as the input signal of Pin13, Pin14.
There is no input at another pins.
5. Inputs 5V at Pin15, confirm that there is no signal output from T.P29, T.P.26, T.P.23, T.P.21,
T.P.18,T.P.17.
6. Decreasing gradually the voltage of terminal Pin 15. Read the voltage when there are signals
output from the terminals listed as above. The voltage is as Vsth2.
note20) The condition is as table 1. SG8 of luminance 0% is the input signal of Pin20. Increase sync level
from 0Vp-p to 0.02Vp-p. Confirm outputting no pluse.
note21) The condition is as table 1. SG8 of luminance 100%(or 0%) is the input signal of Pin20. Decrease
sync level from 0.3Vp-p to 0.2Vp-p. Confirm no malfunction produced by noise.
note22) The condition is as table 1. SG8 of luminance 100%(or 0%) is the input signal of Pin20. Measure
the high(low) at SyncOUT. The measured value is treated as V
SH
(V
SL
).
note23) The condition is as table 1. SG8 of luminance 100%(or 0%) is the input signal of Pin20. SyncOUT
becomes High with sync part of SG8. Measure the time needed for the front(rear) edge of SG8
sync to fall(rise) from 50% and for SyncOUT to rise(fall) from 50% with an active prove. The
measured value is treated as Tdsf(Tdsr).
SG8
(50%)
Tdsr
Tdsf
(50%)
SyncOUT
sync(50%)
Pedestal voltage
15
相關PDF資料 |
PDF描述 |
|---|---|
| M52756 | WIDE BAND ANALOG SWITCH |
| M52757FP | WIDE BAND ANALOG SWITCH |
| M52758FP | WIDE BAND ANALOG SWITCH |
| M52758SP | WIDE BAND ANALOG SWITCH |
| M52759SP | UNIFORMITY FOR CRT DISPLAY MONITOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M52757FP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:WIDE BAND ANALOG SWITCH |
| M52758FP | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Wide Band Analog Switch |
| M52758SP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:WIDE BAND ANALOG SWITCH |
| M52759SP | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Uniformity for CRT Display Monitor |
| M5275EVB | 制造商:Freescale Semiconductor 功能描述:BOARD EVAL FOR MCF5274/75 |
發布緊急采購，3分鐘左右您將得到回復。