- 您現在的位置：買賣IC網 > PDF目錄370965 > M52756SP (Mitsubishi Electric Corporation) WIDE BAND ANALOG SWITCH PDF資料下載
參數資料
| 型號： | M52756SP |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | WIDE BAND ANALOG SWITCH |
| 中文描述： | 寬頻帶模擬開關 |
| 文件頁數： | 13/19頁 |
| 文件大小： | 585K |
| 代理商： | M52756SP |
M52756SP
WIDE BAND ANALOG SWITCH
MITSUBISHI ICs (Monitor)
ELECTRIC
(
/ 19 )
MITSUBISHI
note ) It omits the SW.No accorded with signal input pin because it is already written in Table 1.
SW A is in side a if there is not defined specially.
note1) The condition is shown as Table 1. Set SW15 to GND(or OPEN) and SW A to side b, measure the
current by current meter A(or B). The current is as Icc1(Icc2,Icc3).
note2) Set SW15 to GND (or OPEN), measure the DC voltage of T.P.29(T.P.26,T.P.23) when there is no
signal input.The DC voltage is as V
DC
1(or V
DC
2).
note3) Measure the DC voltage of T.P.21 same as note2, the DC voltage is as V
DC
3(or V
DC
4).
note4) Set SW15 to GND, SG1 as the input signal of Pin 1.Rising up the amplitude of SG1 slowly, read the
amplitude of input signal when the output waveform is distorted. The amplitude is as Vimax1. And
measure Vimax1 when SG1 as the input signal of Pin 3,Pin 5 in same way.
Next, set SW 15 to OPEN, measure Vimax2 when SG1 as the input signal of Pin8, 10, 12.
note5) 1. The condition is shown as Table 1.
2. Set SW15 to GND, SG2 as the input signal of Pin 1. At this time, read the amplitude output from
T.P 29. The amplitude is as V
OR
1.
3. Voltage gain Gv1 is
G
V
1= 20 LOG
4. The method as same as 2 and 3, measure the voltage gain Gv1 when SG2 as the input signal of
Pin 3, 5.
5. The difference of each channel relative voltage gain is as
Gv1.
Gv1=Gv1R-Gv1B,Gv1B-Gv1G,Gv1G-Gv1R
6. Set SW15 to OPEN, measure Gv2,
Gv2 in the same way.
note5') Voltage gain
Gv' is
Gv'=Gv1R-Gv2R,Gv1G-Gv2G,Gv1B-Gv2B
note6) 1. The condition is shown as table 1. This test is by active probe.
2. Measure the amplitude output from T.P.21.
3. Measure the G
V
3,G
V
4 by the same way as note5.
note7) 1. The condition is shown as table 1. This test is by active probe.
2. Set SW15 to GND, SG2 as the input signal of Pin 1. Measure the amplitude output from T.P.29.
The amplitude is as V
OR
1.By the same way, measure the output when SG4 is as input signal of
Pin 1, the output is as V
OR
2.
3. The frequency characteristic Fc1 is
4. The method as same as 2 and 3, measure the frequency Fc1 when input signal to Pin 3, 5.
5. The difference between of each channel frequency characteristic is as
Fc1.
6. Set SW15 to OPEN, measure Fc2,
Fc2.
note8) By the same way as Note7 measure the Fc3, Fc4 when SG5 of input signal.
note9) 1. The condition is shown as Table1. This test is by active prove.
2. Set SW15 to GND, SG3 as the input signal of Pin 1. Measure the amplitude output from T.P.29.
The amplitude is as V
OR
3.
3. Set SW15 to OPEN, measure the amplitude output from T.P.29. The amplitude is as V
OR
3'.
4. The crosstalk between two inputs C.T.I.1 is
5. By the same way, measure the crosstalk between two inputs when SG3 as the input
signal of Pin3, Pin 5.
0.7 [Vp-p]
V
OR
1 [Vp-p]
[dB]
F
C
1 = 20 LOG
V
OR
1 [Vp-p]
V
OR
2 [Vp-p]
[dB]
C.T.I.1= 20 LOG
V
OR
3 [Vp-p]
V
OR
3' [Vp-p]
[dB]
13
相關PDF資料 |
PDF描述 |
|---|---|
| M52756 | WIDE BAND ANALOG SWITCH |
| M52757FP | WIDE BAND ANALOG SWITCH |
| M52758FP | WIDE BAND ANALOG SWITCH |
| M52758SP | WIDE BAND ANALOG SWITCH |
| M52759SP | UNIFORMITY FOR CRT DISPLAY MONITOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M52757FP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:WIDE BAND ANALOG SWITCH |
| M52758FP | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Wide Band Analog Switch |
| M52758SP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:WIDE BAND ANALOG SWITCH |
| M52759SP | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Uniformity for CRT Display Monitor |
| M5275EVB | 制造商:Freescale Semiconductor 功能描述:BOARD EVAL FOR MCF5274/75 |
發布緊急采購，3分鐘左右您將得到回復。