- 您現在的位置：買賣IC網 > PDF目錄296402 > M50FW016N5G (意法半導體) 16 Mbit 2Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory PDF資料下載
參數資料
| 型號： | M50FW016N5G |
| 廠商： | 意法半導體 |
| 英文描述： | 16 Mbit 2Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
| 中文描述： | 16兆位的2Mb × 8，統一座3V電源閃存固件集線器 |
| 文件頁數： | 14/45頁 |
| 文件大?。?/td> | 673K |
| 代理商： | M50FW016N5G |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁
21/45
M50FW016
hardware reset. If it is set to ‘1’ it should be reset
before a new Program or Erase command is is-
sued, otherwise the new command will appear to
fail.
Program Suspend Status (Bit 2). The Program
Suspend Status bit indicates that a Program oper-
ation has been suspended and is waiting to be re-
sumed. The Program Suspend Status should only
be considered valid when the Program/Erase
Controller Status bit is ‘1’ (Program/Erase Control-
ler inactive); after a Program/Erase Suspend com-
mand is issued the memory may still complete the
operation rather than entering the Suspend mode.
When the Program Suspend Status bit is ‘0’ the
Program/Erase Controller is active or has complet-
ed its operation; when the bit is ‘1’ a Program/
Erase Suspend command has been issued and
the memory is waiting for a Program/Erase Re-
sume command.
When a Program/Erase Resume command is is-
sued the Program Suspend Status bit returns to
‘0’.
Block Protection Status (Bit 1). The Block Pro-
tection Status bit can be used to identify if the Pro-
gram or Block Erase operation has tried to modify
the contents of a protected block. When the Block
Protection Status bit is to ‘0’ no Program or Block
Erase operations have been attempted to protect-
ed blocks since the last Clear Status Register
command or hardware reset; when the Block Pro-
tection Status bit is ‘1’ a Program or Block Erase
operation has been attempted on a protected
block.
Once it is set to ‘1’ the Block Protection Status bit
can only be reset to ‘0’ by a Clear Status Register
command or a hardware reset. If it is set to ‘1’ it
should be reset before a new Program or Block
Erase command is issued, otherwise the new
command will appear to fail.
Using the A/A Mux Interface the Block Protection
Status bit is always ‘0’.
Reserved (Bit 0). Bit 0 of the Status Register is
reserved. Its value should be masked.
Table 11. Status Register Bits
Note: 1. For Program operations during Erase Suspend Bit 6 is ‘1’, otherwise Bit 6 is ‘0’.
Operation
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Program active
‘0’
X(1)
‘0’
Program suspended
‘1
X(1)
‘0’
‘1’
‘0’
Program completed successfully
‘1’
X(1)
‘0’
Program failure due to VPP Error
‘1’
X(1)
‘0’
‘1’
‘0’
Program failure due to Block Protection (FWH Interface only)
‘1’
X(1)
‘0’
‘1’
Program failure due to cell failure
‘1’
X(1)
‘0’
‘1’
‘0’
Erase active
‘0’
Block Erase suspended
‘1’
‘0’
Erase completed successfully
‘1’
‘0’
Erase failure due to VPP Error
‘1’
‘0’
‘1’
‘0’
Block Erase failure due to Block Protection (FWH Interface
only)
‘1’
‘0’
‘1’
Erase failure due to failed cell(s)
‘1’
‘0’
‘1’
‘0’
相關PDF資料 |
PDF描述 |
|---|---|
| M50FW080K1 | 8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
| M50FW080K1G | 8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
| M50FW080NB5T | 8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
| M50FW080NB5TG | 8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
| M524-012.8M | TCVCXO, CLOCK, 12.8 MHz, CMOS OUTPUT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M50FW016N5T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:16 Mbit 2Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
| M50FW016N5TG | 功能描述:閃存 SERIAL FLASH RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| M50FW040 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:4 Mbit 512Kb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
| M50FW040_06 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:4-Mbit (512 Kb x8, uniform block) 3-V supply firmware hub Flash memory |
| M50FW040K | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:4 Mbit 512Kb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
發布緊急采購，3分鐘左右您將得到回復。