- 您現在的位置：買賣IC網 > PDF目錄180226 > M50FLW080AN5T (STMICROELECTRONICS) 1M X 8 FLASH 3V PROM, 11 ns, PDSO40 PDF資料下載
參數資料
| 型號： | M50FLW080AN5T |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | PROM |
| 英文描述： | 1M X 8 FLASH 3V PROM, 11 ns, PDSO40 |
| 封裝： | 10 X 20 MM, PLASTIC, TSOP-40 |
| 文件頁數： | 11/53頁 |
| 文件大?。?/td> | 945K |
| 代理商： | M50FLW080AN5T |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁
19/53
M50FLW080A, M50FLW080B
Once the command is issued, subsequent Bus
Read operations read the value in the Status Reg-
ister. (See the section on the Status Register for
details on the definitions of the Status Register
bits.)
If the address falls in a protected block, the Pro-
gram operation will abort, the data in the memory
array will not be changed, and the Status Register
will indicate the error.
During the Program operation, the memory will
only accept the Read Status Register command
and the Program/Erase Suspend command. All
other commands are ignored.
See Figure 22., for a suggested flowchart on using
the Program command. Typical Program times are
given in Table 18..
Quadruple Byte Program Command (A/A Mux
Interface). The Quadruple Byte Program Com-
mand is used to program four adjacent Bytes in
the memory array at a time. The four Bytes must
differ only for addresses A0 and A1. Programming
should not be attempted when VPP is not at VPPH.
Five Bus Write operations are required to issue the
command. The second, third and fourth Bus Write
cycles latch the respective addresses and data of
the first, second and third Bytes in the Program/
Erase Controller. The fifth Bus Write cycle latches
the address and data of the fourth Byte and starts
the Program/Erase Controller. Once the command
is issued, subsequent Bus Read operations read
the value in the Status Register. (See the section
on the Status Register for details on the definitions
of the Status Register bits.)
During the Quadruple Byte Program operation, the
memory will only accept the Read Status Register
and Program/Erase Suspend commands. All other
commands are ignored.
Note that the Quadruple Byte Program command
cannot change a bit set to ‘0’ back to ‘1’ and at-
tempting to do so will not modify its value. One of
the erase commands must be used to set all of the
bits in the block to ‘1’.
See Figure 24., for a suggested flowchart on using
the Quadruple Byte Program command. Typical
Quadruple Byte Program times are given in Table
Double/Quadruple Byte Program Command
(FWH Mode). The Double/Quadruple Byte Pro-
gram Command can be used to program two/four
adjacent Bytes to the memory array at a time. The
two Bytes must differ only for address A0; the four
Bytes must differ only for addresses A0 and A1.
Two Bus Write operations are required to issue the
command. The second Bus Write cycle latches the
start address and two/four data Bytes and starts
the Program/Erase Controller. Once the command
is issued, subsequent Bus Read operations read
the contents of the Status Register. (See the sec-
tion on the Status Register for details on the defi-
nitions of the Status Register bits.)
During the Double/Quadruple Byte Program oper-
ation the memory will only accept the Read Status
register and Program/Erase Suspend commands.
All other commands are ignored.
Note that the Double/Quadruple Byte Program
command cannot change a bit set to ‘0’ back to ‘1’
and attempting to do so will not modify its value.
One of the erase commands must be used to set
all of the bits in the block to ‘1’.
See Figure 23., for a suggested flowchart on using
the Double/Quadruple Byte Program command.
Typical Double/Quadruple Byte Program times
are given in Table 18..
Chip Erase Command. The Chip Erase Com-
mand erases the entire memory array, setting all
of the bits to ‘1’. All previous data in the memory
array are lost. This command, though, is only
available under the A/A Mux interface.
Two Bus Write operations are required to issue the
command, and to start the Program/Erase Con-
troller. Once the command is issued, subsequent
Bus Read operations read the contents of the Sta-
tus Register. (See the section on the Status Reg-
ister for details on the definitions of the Status
Register bits.)
Erasing should not be attempted when VPP is not
at VPPH, otherwise the result is uncertain.
During the Chip Erase operation, the memory will
only accept the Read Status Register command.
All other commands are ignored.
See Figure 26., for a suggested flowchart on using
the Chip Erase command. Typical Chip Erase
times are given in Table 18..
Block Erase Command. The Block Erase com-
mand is used to erase a block, setting all of the bits
to ‘1’. All previous data in the block are lost.
Two Bus Write operations are required to issue the
command. The second Bus Write cycle latches the
block address and starts the Program/Erase Con-
troller. Once the command is issued, subsequent
Bus Read operations read the contents of the Sta-
tus Register. (See the section on the Status Reg-
ister for details on the definitions of the Status
Register bits.)
If the block, or if at least one sector of the block (for
the blocks that are split into sectors), is protected
(FWH/LPC only) then the Block Erase operation
will abort, the data in the block will not be changed,
and the Status Register will indicate the error.
During the Block Erase operation the memory will
only accept the Read Status Register and Pro-
gram/Erase Suspend commands. All other com-
mands are ignored.
相關PDF資料 |
PDF描述 |
|---|---|
| M510-007-04-03 | 1 CONTACT(S), GLASS FILLED POLYFORMALDEHYDE POLYETHYLENE, FEMALE, CIRCULAR CONNECTOR, SOLDER, JACK |
| M510-009-03-00 | 1 CONTACT(S), GLASS FILLED POLYFORMALDEHYDE POLYETHYLENE, FEMALE, CIRCULAR CONNECTOR, SOLDER, JACK |
| M510-009-03-01 | 1 CONTACT(S), GLASS FILLED POLYFORMALDEHYDE POLYETHYLENE, FEMALE, CIRCULAR CONNECTOR, SOLDER, JACK |
| M510-009-03-03 | 1 CONTACT(S), GLASS FILLED POLYFORMALDEHYDE POLYETHYLENE, FEMALE, CIRCULAR CONNECTOR, SOLDER, JACK |
| M510-009-04-00 | 1 CONTACT(S), GLASS FILLED POLYFORMALDEHYDE POLYETHYLENE, FEMALE, CIRCULAR CONNECTOR, SOLDER, JACK |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M50FLW080AN5TG | 功能描述:IC FLASH 8MBIT 33MHZ 40TSOP RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:1,000 系列:- 格式 - 存儲器:RAM 存儲器類型:移動 SDRAM 存儲容量:256M（8Mx32） 速度:133MHz 接口:并聯 電源電壓:1.7 V ~ 1.95 V 工作溫度:-40°C ~ 85°C 封裝/外殼:90-VFBGA 供應商設備封裝:90-VFBGA（8x13） 包裝:帶卷 (TR) 其它名稱:557-1327-2 |
| M50FLW080AN5TP | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Mbit (13 x 64KByte Blocks + 3 x 16 x 4KByte Sectors), 3V Supply Firmware Hub / Low Pin Count Flash Memory |
| M50FLW080ANB5 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Mbit (13 x 64KByte Blocks + 3 x 16 x 4KByte Sectors), 3V Supply Firmware Hub / Low Pin Count Flash Memory |
| M50FLW080ANB5G | 功能描述:閃存 8Mbit 3V Firmwre Hub Low pin-count flash RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| M50FLW080ANB5P | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Mbit (13 x 64KByte Blocks + 3 x 16 x 4KByte Sectors), 3V Supply Firmware Hub / Low Pin Count Flash Memory |
發布緊急采購，3分鐘左右您將得到回復。