參數資料
型號: M37630M4T-XXXFP
廠商: Mitsubishi Electric Corporation
英文描述: SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
中文描述: 單芯片8位CMOS微機
文件頁數: 20/48頁
文件大?。?/td> 563K
代理商: M37630M4T-XXXFP
MITSUBISHI
ELECTRIC
20
MITSUBISHI MICROCOMPUTERS
7630 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Fig. 18
Structure of Timer X mode register
Timer Y
Timer Y is a 16 bit timer with a 16-bit reload latch supporting the fol-
lowing operating modes:
(1) Timer mode
(3) Event counter mode
(5) Pulse period measurement mode
(6) H/L pulse width measurement mode
These modes can be selected by the timer Y mode register (TYM).
In the timer, pulse period- and pulse width measurement modes’
the timer’s count source can be selected by the timer Y count
source selection bits. Please refer to Fig. 19.
On read or write access to timer Y, note that the high-order and low-
order bytes must be accessed in a specific order.
Write method
When writing to timer Y, write the low-order byte first. The data writ-
ten is stored in a temporary register which is assigned to the same
address as TY
L
. Next, write the high-order byte. When this is fin-
ished, the data is placed in the timer Y high-order reload latch and
the low-order byte is transferred from its temporary register to the
timer Y low-order reload latch.
Read method
When reading the timer Y, read the high-order byte first. This
causes the timer Y high- and low-order bytes to be transferred to
temporary registers being assigned to the same addresses as TY
H
and TY
L
. Next, read the low-order byte which is read from the tem-
porary register. This method assures the correct timer value can be
read during timer count operation.
Timer Y count stop control
Regardless of the actual operating mode, timer Y can be stopped
by setting the timer Y count stop bit (bit 7 of the timer Y mode regis-
ter) to “1”.
Timer X data write control bit
0 :
Data is written to latch and timer
1 :
Data is written to latch only
Not used (“0” when read, do not write “1”)
Timer X mode bits
b5 b4
0 0: Timer mode
0 1: Bi-phase counter mode
1 0: Event counter mode
1 1: Pulse width measurement mode
CNTR
0
polarity selection bit
0 :
For event counter mode, rising edge active
For interrupt request, falling edge active
For pulse width measurement mode, measure “H” period
1 :
For event counter mode, falling edge active
For interrupt request, rising edge active
For pulse width measurement mode, measure “L” period
Timer X stop control bit
0 :
Timer counting
1 :
Timer stopped
7
0
Timer X mode register (address 001E
16
)
TXM
相關PDF資料
PDF描述
M37630M4T-XXXFS SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37640M4T SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37630 Single Chip 8 Bits CMOS Microcomputer(8位單片機)
M37630E4FS SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37630E4T-XXXFP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
相關代理商/技術參數
參數描述
M37630M4T-XXXFS 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37630T-RFS 功能描述:BOARD CONV FOR M37630 EMULATOR RoHS:否 類別:編程器,開發系統 >> 配件 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program RoHS指令信息:IButton RoHS Compliance Plan 標準包裝:1 系列:- 附件類型:USB 至 1-Wire? RJ11 適配器 適用于相關產品:1-Wire? 設備 產品目錄頁面:1429 (CN2011-ZH PDF)
M37632EFFS 功能描述:EPROM MCU/8BIT CMOS EMULATION CH RoHS:否 類別:編程器,開發系統 >> 配件 系列:- 標準包裝:1 系列:- 附件類型:適配器板 適用于相關產品:RCB230,RCB231,RCB212 配用:26790D-ND - RCB BREAKOUT BOARD RS232 CABLE
M37632RFS 功能描述:EMULATION MCU/8BIT CMOS EMULATIO RoHS:否 類別:編程器,開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 傳感器類型:CMOS 成像,彩色(RGB) 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP
M3763A 制造商:未知廠家 制造商全稱:未知廠家 功能描述:HORN/SIREN WITH SOFT CHIRP 6 ALARM SOUNDS