參數資料
型號: M37534M4-XXXGP
廠商: Mitsubishi Electric Corporation
英文描述: SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
中文描述: 單芯片8位CMOS微機
文件頁數: 33/55頁
文件大?。?/td> 610K
代理商: M37534M4-XXXGP
7534 Group
Rev.2.00 Jun 21, 2004 page 33 of 54
REJ03B0099-0200Z
Watchdog Timer
The watchdog timer gives a means for returning to a reset status
when the program fails to run on its normal loop due to a runaway.
The watchdog timer consists of an 8-bit watchdog timer H and an 8-
bit watchdog timer L, being a 16-bit counter.
Standard operation of watchdog timer
The watchdog timer stops when the watchdog timer control register
(address 0039
16
) is not set after reset. Writing an optional value to
the watchdog timer control register (address 0039
16
) causes the
watchdog timer to start to count down. When the watchdog timer H
underflows, an internal reset occurs. Accordingly, it is programmed
that the watchdog timer control register (address 0039
16
) can be set
before an underflow occurs.
When the watchdog timer control register (address 0039
16
) is read,
the values of the high-order 6-bit of the watchdog timer H, STP in-
struction disable bit and watchdog timer H count source selection bit
are read.
Initial value of watchdog timer
By a reset or writing to the watchdog timer control register (address
0039
16
), the watchdog timer H is set to “FF
16
” and the watchdog
timer L is set to “FF
16
”.
Operation of watchdog timer H count source selection bit
A watchdog timer H count source can be selected by bit 7 of the
watchdog timer control register (address 0039
16
). When this bit is
“0”, the count source becomes a watchdog timer L underflow signal.
The detection time is 174.763 ms at f(X
IN
)=6 MHz.
When this bit is “1”, the count source becomes f(X
IN
)/16. In this
case, the detection time is 683 μs at f(X
IN
)=6 MHz.
This bit is cleared to “0” after reset.
Operation of STP instruction disable bit
When the watchdog timer is in operation, the STP instruction can be
disabled by bit 6 of the watchdog timer control register (address
0039
16
).
When this bit is “0”, the STP instruction is enabled.
When this bit is “1”, the STP instruction is disabled, and an internal
reset occurs if the STP instruction is executed.
Once this bit is set to “1”, it cannot be changed to “0” by program.
This bit is cleared to “0” after reset.
Fig. 38 Block diagram of watchdog timer
Fig. 39 Structure of watchdog timer control register
X
IN
Data bus
“0”
“1”
Watchdog timer H count
source selection bit
1/16
Reset
circuit
STP Instruction Disable Bit
STP Instruction
Watchdog timer H (8)
Write “FF
16
” to the
watchdog timer
control register
Internal reset
RESET
Watchdog timer L (8)
Write “FF
16
” to the
watchdog timer
control register
Watchdog timer control register(address 0039
16
)
WDTCON
Watchdog timer H (read-only for high-order 6-bit)
STP instruction disable bit
0 : STP instruction enabled
1 : STP instruction disabled
Watchdog timer H count source selection bit
0 : Watchdog timer L underflow
1 : f(X
IN
)/16
b7 b0
相關PDF資料
PDF描述
MAN6940E 0.56 INCH (14.2 MM) DUAL DIGIT STICK DISPLAY
MAN6910E 0.56 INCH (14.2 MM) DUAL DIGIT STICK DISPLAY
ML2252 μP Compatible 8-Bit A/D Converters with 2-Channel Multiplexer(具有雙通道多路轉換器的微處理器兼容的8位A/D轉換器)
ML2258 μP Compatible 8-Bit A/D Converters with 8-Channel Multiplexer(具有八通道多路轉換器的微處理器兼容的8位A/D轉換器)
ML2259 μP Compatible 8-Bit A/D Converters with 8-Channel Multiplexer(具有八通道多路轉換器的微處理器兼容的8位A/D轉換器)
相關代理商/技術參數
參數描述
M37534M4-XXXSP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37534RSS 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37536E8SP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37536M4 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37536M4-XXXSP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER