- 您現在的位置：買賣IC網 > PDF目錄384636 > M37534 (Mitsubishi Electric Corporation) Single Chip 8 Bits CMOS Microcomputer(8位單片機) PDF資料下載
參數資料
| 型號： | M37534 |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | Single Chip 8 Bits CMOS Microcomputer(8位單片機) |
| 中文描述： | 單芯片的CMOS 8位單片機（8位單片機） |
| 文件頁數： | 36/53頁 |
| 文件大?。?/td> | 621K |
| 代理商： | M37534 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁當前第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
7534 Group
MITSUBISHI MICROCOMPUTERS
36
PRELIMINARY
Notice: This is not a final specification.
Some parametric limits are subject to change.
Fig. 43 External circuit of ceramic resonator
Fig. 44 External clock input circuit
Fig. 45 Structure of MISRG
Clock Generating Circuit
An oscillation circuit can be formed by connecting a resonator be-
tween X
IN
and X
OUT
.
Use the circuit constants in accordance with the resonator
manufacturer's recommended values. No external resistor is needed
between X
IN
and X
OUT
since a feed-back resistor exists on-chip.
G
Oscillation control
Stop mode
When the STP instruction is executed, the internal clock
φ
stops at
an “H” level and the X
IN
oscillator stops. At this time, timer 1 is set to
“01
16
” and prescaler 12 is set to “FF
16
” when the oscillation
stabilization time set bit after release of the STP instruction is “0”.
On the other hand, timer 1 and prescaler 12 are not set when the
above bit is “1”. Accordingly, set the wait time fit for the oscillation
stabilization time of the oscillator to be used.
f(X
IN
)/16 is forcibly connected to the input of prescaler 12.
When an external interrupt is accepted, oscillation is restarted but
the internal clock
φ
remains at “H” until timer 1 underflows. As soon
as timer 1 underflows, the internal clock
φ
is supplied. This is
because when a ceramic oscillator is used, some time is required
until a start of oscillation.
In case oscillation is restarted by reset, no wait time is generated.
So apply an “L” level to the RESET pin while oscillation becomes
stable.
Wait mode
If the WIT instruction is executed, the internal clock
φ
stops at an
“H” level, but the oscillator does not stop. The internal clock restarts
if a reset occurs or when an interrupt is received.
Since the oscillator does not stop, normal operation can be started
immediately after the clock is restarted.
To ensure that interrupts will be received to release the STP or WIT
state, interrupt enable bits must be set to “1” before the STP or
WIT instruction is executed.
When the STP status is released, prescaler 12 and timer 1 will start
counting clock which is X
IN
divided by 16, so set the timer 1 inter-
rupt enable bit to “0” before the STP instruction is executed.
Note
For use with the oscillation stabilization set bit after release of the
STP instruction set to “1”, set values in timer 1 and prescaler
12 after fully appreciating the oscillation stabilization time of the
oscillator to be used.
Clock mode
Operation is started by a built-in ring oscillator after releasing reset.
A division ratio (1/1,1/2,1/8) is selected by setting bits 7 and 6 of the
CPU mode register after releasing it.
X
IN
C
OUT
C
IN
X
OUT
X
IN
X
OUT
External oscillation
circuit
V
CC
V
SS
Open
MISRG(Address 0038
16
)
b7 b0
Oscillation stabilization time set bit after
release of the STP instruction
0: Set “01
16
” in timer1, and “FF
16
”
in prescaler 12 automatically
1: Not set automatically
Reserved bits (return “0” when read)
(Do not write “1” to these bits)
Not used (return “0” when read)
相關PDF資料 |
PDF描述 |
|---|---|
| M37700 | 16-Bit Single-Chip Microcomputer(16位單片微控制器) |
| M37721 | 16-Bit Single-Chip Microcomputer(16位單片微控制器) |
| M37733MHB | Single Chip 16 Bits CMOS Microcomputer(16位單片機) |
| M37735S4L | Single Chip 16 Bits CMOS Microcomputer(16位單片機) |
| M37736MHL | Single Chip 16 Bits CMOS Microcomputer(16位單片機) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37534E4FP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37534E4GP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37534E4GP#U1 | 功能描述:MCU 4/5V 8K PB-FREE 32-LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 產品培訓模塊:CAN Basics Part-1 CAN Basics Part-2 Electromagnetic Noise Reduction Techniques Part 1 M16C Product Overview Part 1 M16C Product Overview Part 2 標準包裝:1 系列:M16C™ M32C/80/87 核心處理器:M32C/80 芯體尺寸:16/32-位 速度:32MHz 連通性:EBI/EMI，I²C，IEBus，IrDA，SIO，UART/USART 外圍設備:DMA，POR，PWM，WDT 輸入/輸出數:121 程序存儲器容量:384KB（384K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:24K x 8 電壓 - 電源 (Vcc/Vdd):3 V ~ 5.5 V 數據轉換器:A/D 34x10b，D/A 2x8b 振蕩器型:內部 工作溫度:-20°C ~ 85°C 封裝/外殼:144-LQFP 包裝:托盤 產品目錄頁面:749 (CN2011-ZH PDF) 配用:R0K330879S001BE-ND - KIT DEV RSK M32C/87 |
| M37534E8FP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37534E8SP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。