- 您現在的位置：買賣IC網 > PDF目錄384636 > M37531 (Mitsubishi Electric Corporation) Single Chip 8 Bits CMOS Microcomputer(8位單片機) PDF資料下載
參數資料
| 型號： | M37531 |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | Single Chip 8 Bits CMOS Microcomputer(8位單片機) |
| 中文描述： | 單芯片的CMOS 8位單片機（8位單片機） |
| 文件頁數： | 30/64頁 |
| 文件大?。?/td> | 631K |
| 代理商： | M37531 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
7531 Group
MITSUBISHI MICROCOMPUTERS
30
Clock Generating Circuit
An oscillation circuit can be formed by connecting a resonator be-
tween X
IN
and X
OUT
, and an RC oscillation circuit can be formed by
connecting a resistor and a capacitor.
Use the circuit constants in accordance with the resonator
manufacturer's recommended values. No external resistor is needed
between X
IN
and X
OUT
since a feed-back resistor exists on-chip.
Set the constants of the resistor and capacitor when an RC oscillator
is used, so that a frequency variation due to LSI variation and resis-
tor and capacitor variations may not exceed the standard input fre-
quency.
G
Oscillation control
Stop mode
When the STP instruction is executed, the internal clock f stops at
an “H” level and the X
IN
oscillator stops. At this time, timer 1 is set
to “01
16
” and prescaler 12 is set to “FF
16
” when the oscillation sta-
bilization time set bit after release of the STP instruction is “0”. On
the other hand, timer 1 and prescaler 12 are not set when the
above bit is “1”. Accordingly, set the wait time fit for the oscillation
stabilization time of the oscillator to be used. f(X
IN
)/16 is forcibly
connected to the input of prescaler 12. When an external interrupt
is accepted, oscillation is restarted but the internal clock f remains
at “H” until timer 1 underflows. As soon as timer 1 underflows, the
internal clock f is supplied. This is because when a ceramic oscilla-
tor is used, some time is required until a start of oscillation. In case
oscillation is restarted by reset, no wait time is generated. So apply
an “L” level to the RESET pin while oscillation becomes stable.
Wait mode
If the WIT instruction is executed, the internal clock f stops at an “H”
level, but the oscillator does not stop. The internal clock restarts if
a reset occurs or when an interrupt is received. Since the oscillator
does not stop, normal operation can be started immediately after
the clock is restarted. To ensure that interrupts will be received to
release the STP or WIT state, interrupt enable bits must be set to
“1” before the STP or WIT instruction is executed.
When the STP status is released, prescaler 12 and timer 1 will start
counting clock which is X
IN
divided by 16, so set the timer 1 inter-
rupt enable bit to “0” before the STP instruction is executed.
Note
For use with the oscillation stabilization set bit after release of the
STP instruction set to “1”, set values in timer 1 and prescaler
12 after fully appreciating the oscillation stabilization time of the
oscillator to be used.
G
Switch of ceramic and RC oscillations
After releasing reset the operation starts by starting a built-in ring
oscillator. Then, a ceramic oscillation or an RC oscillation is selected
by setting bit 5 of the CPU mode register.
The bit 5 can be rewritten only once after releasing reset. However,
after rewriting it is disable to write any value to the bit.
G
Double-speed mode
When a ceramic oscillation is selected, a double-speed mode can be
used. Do not use it when an RC oscillation is selected.
相關PDF資料 |
PDF描述 |
|---|---|
| M37534 | Single Chip 8 Bits CMOS Microcomputer(8位單片機) |
| M37700 | 16-Bit Single-Chip Microcomputer(16位單片微控制器) |
| M37721 | 16-Bit Single-Chip Microcomputer(16位單片微控制器) |
| M37733MHB | Single Chip 16 Bits CMOS Microcomputer(16位單片機) |
| M37735S4L | Single Chip 16 Bits CMOS Microcomputer(16位單片機) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37531E4FP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37531E4FP#U0 | 制造商:Renesas Electronics Corporation 功能描述:MITSUBISHI 8 BIT OTP MCU |
| M37531E4GP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37531E4SP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37531E8FP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。