參數資料
型號： M3455AG8-XXXFP
元件分類： 微控制器/微處理器
英文描述： 4-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PQFP52
封裝： 10 X 10 MM, 0.65 MM PITCH, PLASTIC, LQFP-52
文件頁數： 120/148頁
文件大?。?/td> 1807K
代理商： M3455AG8-XXXFP
Rev.1.02
Nov 26, 2008
Page 73 of 146
REJ03B0224-0102
455A Group
NOTES ON NOISE
Countermeasures against noise are described below.
The following countermeasures are effective against noise in
theory, however, it is necessary not only to take measures as
follows but to evaluate before actual use.
(1) Shortest wiring length
The wiring on a printed circuit board can function as an antenna
which feeds noise into the microcomputer.
The shorter the total wiring length (by mm unit), the less the
possibility of noise insertion into a microcomputer.
(1) Wiring for RESET input pin
Make the length of wiring which is connected to the RESET
input pin as short as possible.
Especially, connect a capacitor across the RESET input pin
and the VSS pin with the shortest possible wiring.
Reason
In order to reset a microcomputer correctly, 1 machine cycle or
more of the width of a pulse input into the RESET pin is
required.
If noise having a shorter pulse width than this is input to the
RESET input pin, the reset is released before the internal state
of the microcomputer is completely initialized.
This may cause a program runaway.
Fig 72. Wiring for the RESET input pin
(2) Wiring for clock input/output pins
Make the length of wiring which is connected to clock I/O
pins as short as possible.
Make the length of wiring across the grounding lead of a
capacitor which is connected to an oscillator and the VSS
pin of a microcomputer as short as possible.
Separate the VSS pattern only for oscillation from other
VSS patterns.
Fig 73. Wiring for clock I/O pins
Reason
If noise enters clock I/O pins, clock waveforms may be
deformed. This may cause a program failure or program
runaway.
Also, if a potential difference is caused by the noise between
the VSS level of a microcomputer and the VSS level of an
oscillator, the correct clock will not be inpu t in the
microcomputer.
(3) Wiring to CNVSS pin
Connect an approximately 5 k
resistor to the VPP pin and
also to the GND pattern supplied to the VSS pin with
shortest possible wiring.
Reason
The CNVSS pin is the power source input pin for the built-in
QzROM. When programming in the built-in QzROM, the
impedance of the CNVSS pin is low to allow the electric
current for writing flow into the QzROM. Because of this,
noise can enter easily. If noise enters the CNVSS pin, abnormal
instruction codes or data are read from the built-in QzROM,
which may cause a program runaway.
Fig 74. Wiring for CNVSS pin
RESET
Reset
circuit
Noise
VSS
N.G.
Reset
circuit
VSS
RESET
VSS
O.K.
Noise
XIN
XOUT
VSS
N.G.
XIN
XOUT
VSS
O.K.
CN V s s
V SS
T h e shorte st
about 5k
N ote : T h is indica te s pin.
(Note)
相關PDF資料
PDF描述
M3455AGCFP 4-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PQFP52
M3455AGC-XXXFP 4-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PQFP52
M3455AG8FP 4-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PQFP52
M3455AGC-XXXFP 4-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PQFP52
M3455AG8-XXXFP 4-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PQFP52
相關代理商/技術參數
參數描述
M3455AGCFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
M3455AGC-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
M3455-SL001 制造商:Alpha Wire 功能描述:
M3455-SL002 制造商:Alpha Wire 功能描述:
M3455-SL005 制造商:Alpha Wire 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*