- 您現在的位置：買賣IC網 > PDF目錄98005 > M34551E8-XXXFP 4-BIT, OTPROM, MICROCONTROLLER, PQFP48 PDF資料下載
參數資料
| 型號： | M34551E8-XXXFP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-BIT, OTPROM, MICROCONTROLLER, PQFP48 |
| 封裝： | 7 X 10 MM, 0.65 MM PITCH, PLASTIC, QFP-48 |
| 文件頁數： | 48/154頁 |
| 文件大?。?/td> | 1778K |
| 代理商： | M34551E8-XXXFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁當前第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁
APPENDIX
3-12
4551 Group User’s Manual
3.3 List of precautions
Noise and latch-up prevention
Connect a capacitor on the following condition to prevent noise
and latch-up;
connect a bypass capacitor (approx. 0.1
F) between pins
VDD and VSS at the shortest distance,
equalize its wiring in width and length, and
use the thickest wire.
In the built-in PROM version, CNVSS pin is also used as VPP
pin. Accordingly, when using this pin, connect this pin to VSS
through a resistor about 5 k
(connect this resistor to CNVSS/
VPP pin as close as possible).
Prescaler
Stop the prescaler operation to change its frequency dividing
ratio.
Count source
Stop timer 1 or timer LC counting to change its count source.
When timer 2 count source changes from f(XCIN) to ORCLK
(W23 = “0”
→ W23 = “1”), the count value of timer 2 is initialized.
However, when timer 2 count source changes from ORCLK to
f(XCIN) (W23 = “1”
→ W23 = “0”) or the same count source is
set again (W23 = “0”
→ W23 = “0” or W23 = “1” → W23 = “1”),
the count value of timer 2 is not initialized.
Timer 2
Timer 2 has the watchdog timer function (WDT). When timer 2
is used as the WDT, note that the processing to initialize the
count value and the execution of the WRST instruction.
Reading the count value
Stop the prescaler and then execute the TAB1 instruction to
read timer 1 data.
Writing to reload register R1
Write the data to reload register R1 while timer 1 is operating,
avoid a timing when timer 1 underflows.
Notes when using the carrier wave output auto-control function
Execute the STCR instruction after setting the timer 1 and
register C2 in order to start the carrier generating circuit
operation.
Stop the timer 1 (W20=“0”) after stopping the carrier
generating circuit (SPCR instruction executed) while the
carrier wave output is disabled in order to stop the carrier
wave output auto-control operation.
If the carrier wave output auto-control function is invalidated
(C20=“0”) while the carrier wave output is auto-controlled,
the output of port CARR retains the state when the auto-
control is invalidated regardless of timer 1 underflow. This
state is released by timer 1 stop (W20=“0”).
When the carrier wave output auto-control function is
validated (C20=“1”) again after it is invalidated (C20=“0”),
the auto-control of carrier wave output is started again when
the next timer 1 underflow occurs. However, when the carrier
wave output auto-control bit is changed during timer 1
underflow, the error-operation may occur.
Use the carrier wave or the carrier wave divided by 2 as the
timer 1 count source when the carrier wave output auto-
control function is selected.
If the ORCLK is used as the count source, a hazard may
occur in port CARR output because ORCLK is not
synchronized with the carrier wave.
When “no carrier wave” is selected with register C1
((C13C12C11C10) = (0101), (1101)), the enable/disable of
the carrier wave output cannot be controlled by the carrier
wave output auto-control function.
D5/INT pin
When the interrupt valid waveform of D5/INT pin is changed
with the bit 2 of register I1 in software, be careful about the
following notes.
Clear the bit 0 of register V1 to “0” and then change the
interrupt valid waveform of D5/INT pin with the bit 2 of register
I1 (refer to Figure 40).
Clear the bit 2 of register I1 to “0” and execute the SNZ0
instruction to clear the EXF0 flag after executing at least
one instruction (refer to Figure 40). Depending on the input
state of the D5/INT pin, the external 0 interrupt request flag
(EXF0) may be set to “1” when the interrupt valid waveform
is changed.
LA
4
; (!!!02)
TV1A
; The SNZ0 instruction is valid
LA
4
TI1A
; Change of the interrupt valid waveform
NOP
SNZ0
;The SNZ0 instruction is executed
NOP
! : this bit is not related to the setting of INT.
...
One Time PROM version
The operating power voltage of the One Time PROM version
is within the range of 2.5 V to 5.5 V.
Multifunction
Note that the port D5 output function can be used even when
INT function is selected.
Power down instruction (POF instruction, POF2 instruction)
Execute the POF or POF2 instruction immediately after
executing the EPOF instruction to enter the power down state.
Note that system cannot enter the power down state when
executing only the POF or POF2 instruction.
Be sure to disable interrupts by executing the DI instruction
before executing the EPOF instrcution.
Program counter
Make sure that the PCH does not specify after the last page of
the built-in ROM.
Fig. 40 External 0 interrupt program example
12
11
相關PDF資料 |
PDF描述 |
|---|---|
| M34554M8-XXXFP | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PQFP64 |
| M34554MC-XXXFP | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PQFP64 |
| M34571G6FP | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO24 |
| M34584EDFP | 4-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PDSO42 |
| M35047-XXXSP | 24 X 12 CHARACTERS CRT CHAR DSPL CTLR, PDIP20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M34551M4 | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:4-BIT SINGLE-CHIP MICROCOMPUTER |
| M34551M4-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER for INFRARED REMOTE CONTROL TRANSMITTER |
| M34551M8 | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:4-BIT SINGLE-CHIP MICROCOMPUTER |
| M34552G8FP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M34552G8HFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。