- 您現在的位置：買賣IC網 > PDF目錄45007 > LX1668CPW-TR (MICROSEMI CORP-ANALOG MIXED SIGNAL GROUP) 1 A SWITCHING CONTROLLER, 250 kHz SWITCHING FREQ-MAX, PDSO20 PDF資料下載
參數資料
| 型號： | LX1668CPW-TR |
| 廠商： | MICROSEMI CORP-ANALOG MIXED SIGNAL GROUP |
| 元件分類： | 穩壓器 |
| 英文描述： | 1 A SWITCHING CONTROLLER, 250 kHz SWITCHING FREQ-MAX, PDSO20 |
| 封裝： | ROHS COMPLIANT, PLASTIC, TSSOP-20 |
| 文件頁數： | 3/15頁 |
| 文件大?。?/td> | 392K |
| 代理商： | LX1668CPW-TR |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁
PROGRAMMABLE MULTIPLE OUTPUT DC:DC CONTROLLER
LX1668
PRODUCT DA T ABOOK 1996/1997
11
Copyright 1999
Rev. 1.0a
P RODUCTION D AT A S HEET
APPLICA TION INFORMA TION
OUTPUT CAPACITOR (continued)
excursion in the transient.
Adaptive voltage positioning in-
creases the value of V
EX,
allowing a higher ESR value and
reducing the cost of the output capacitor.
Typically, the
positioning voltage is 40mV (peak), using the LX1668, and the
transient tolerance is 100mV, resulting in a V
EX of 140mV (see
Figure 4).
Electrolytic capacitors can be used for the output capacitor,
but are less stable with age than tantalum capacitors. As they age,
their ESR degrades, reducing the system performance and
increasing the risk of failure. It is recommended that multiple
parallel capacitors be used, so that, as ESR increases with age,
overall performance will still meet the processor’s requirements.
There is frequently strong pressure to use the least expensive
components possible, however, this could lead to degraded
long-term reliability, especially in the case of filter capacitors.
Linfinity’s demonstration boards use Sanyo MV-GX filter capaci-
tors, which are aluminum electrolytic, and have demonstrated
reliability. The Oscon series from Sanyo generally provides the
very best performance in terms of long term ESR stability and
general reliability, but at a substantial cost penalty. The MV-GX
series provides excellent ESR performance at a reasonable cost.
Beware of off-brand, very low-cost filter capacitors, which have
been shown to degrade in both ESR and general electrolytic
characteristics over time.
INPUT CAPACITOR
The input capacitor and the input inductor are to filter the
pulsating current generated by the buck converter to reduce
interference to other circuits connected to the same 5V rail. In
addition, the input capacitor provides local de-coupling the buck
converter. The capacitor should be rated to handle the RMS
current requirement. The RMS current is:
I
RMS = I L √ d(1-d)
where I
L is the inductor current and the d is the duty cycle. The
maximum value, when d = 50%, I
RMS = 0.5I L.
For 5V input and
output in the range of 2 to 3V, the required RMS current is very
close to 0.5I
L.
A high-frequency (ceramic) capacitor should be placed
across the drain of the top MOSFET and the source of the bottom
one to avoid ringing due to the parasitic inductor being switched
ON and OFF. See capacitor C7 in the Product Highlight.
SOFT-START CAPACITOR
The value of the soft-start capacitor determines how fast the
output voltage rises and how large the inductor current is
required to charge the output capacitor. The output voltage will
follow the voltage at SS pin if the required inductor current does
not exceed the maximum current in the inductor.
SOFT-START CAPACITOR (continued)
The SS pin voltage can be expressed as:
V
SS = VSET (1-e
-t/RssCss)
where V
SET is the output of the DAC. RSS and CSS are soft start
resistor and capacitor, as shown in Figure 4.
The required
inductor current for the output capacitor to follow the SS-pin
voltage equals the required capacitor current plus the load
current. The soft-start capacitor should be selected so that the
overall inductor current does not exceed it maximum.
The capacitor current to follow the SS-pin voltage is:
where C
OUT is the output capacitance. The typical value of CSS
should be in the range of 0.1 to 0.2F.
During the soft-start interval, before the PWRGD signal
becomes valid, the load current from a microprocessor is
negligible; therefore, the capacitor current is approximately the
required inductor current.
CURRENT LIMIT
Current limiting occurs when a sensed voltage, proportional to
load current, exceeds the current-sense comparator threshold
value. The current can be sensed either by using a fixed sense
resistor in series with the inductor to cause a voltage drop
proportional to current, or by using a resistor and capacitor in
parallel with the inductor to sense the voltage drop across the
parasitic resistance of the inductor. The LX1668 has a threshold
of 60mV.
Sense Resistor
The current sense resistor, R
SENSE, is selected according to the
formula:
R
SENSE = VTRIP / ITRIP
Where V
TRIP is the current sense comparator threshold (60mV)
and I
TRIP is the desired current limit. Typical choices are shown
below.
Sense Resistor
Load
Value
Pentium-Class Processor (<10A)
5m
Pentium II Class (>10A)
2.5m
TABLE 2 - Current Sense Resistor Selection Guide
I
Cout = COUT
=* e-(t/RssCss )
dV
dt
C
OUT
C
SS
A smaller sense resistor will result in lower heat dissipation
(IR) and also a smaller output voltage droop at higher currents.
O
B
SO
LETE
PRO
D
UCT
NOT
RECOMMENDED
FOR
NEW
DESIGNS
相關PDF資料 |
PDF描述 |
|---|---|
| LX1668CDWT | 1 A SWITCHING CONTROLLER, 250 kHz SWITCHING FREQ-MAX, PDSO20 |
| LX1671CPW-TR | 1 A SWITCHING CONTROLLER, 345 kHz SWITCHING FREQ-MAX, PDSO38 |
| LX1672-05CPWTR | 1 A DUAL SWITCHING CONTROLLER, 575 kHz SWITCHING FREQ-MAX, PDSO28 |
| LX1672-03CLQTR | 1 A DUAL SWITCHING CONTROLLER, 345 kHz SWITCHING FREQ-MAX, PQCC38 |
| LX1673-03CPWTR | 1 A SWITCHING CONTROLLER, 345 kHz SWITCHING FREQ-MAX, PDSO20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LX1669 | 制造商:MICROSEMI 制造商全稱:Microsemi Corporation 功能描述:PROGRAMMABLE DC : DC CONTROLLER |
| LX1669CD | 功能描述:IC CTRLR DC/DC PROG SW 16SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR) |
| LX1669CDT | 制造商:MICROSEMI 制造商全稱:Microsemi Corporation 功能描述:Current-Mode SMPS Controller |
| LX1670 | 制造商:MICROSEMI 制造商全稱:Microsemi Corporation 功能描述:5 - BIT PROGRAMMABLE VOTAGE REFERENCE |
| LX1670CD | 功能描述:IC REF/MON VOLT 5BIT PROG 14SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。