- 您現在的位置：買賣IC網 > PDF目錄358961 > LV2205 (ON SEMICONDUCTOR) Silicon Tuning Diodes PDF資料下載
參數資料
| 型號： | LV2205 |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 參考電壓二極管 |
| 英文描述： | Silicon Tuning Diodes |
| 中文描述： | 15 pF, 25 V, SILICON, VARIABLE CAPACITANCE DIODE, TO-92 |
| 封裝： | PLASTIC, CASE 182-06, TO-226AC, 2 PIN |
| 文件頁數： | 5/8頁 |
| 文件大小： | 70K |
| 代理商： | LV2205 |
MMBV2101LT1 Series, MV2105, MV2101, MV2109, LV2205, LV2209
http://onsemi.com
5
STEP 1
PREHEAT
ZONE 1
RAMP"
STEP 2
VENT
SOAK"
STEP 3
HEATING
ZONES 2 & 5
RAMP"
STEP 4
HEATING
ZONES 3 & 6
SOAK"
STEP 5
HEATING
ZONES 4 & 7
SPIKE"
STEP 6
VENT
STEP 7
COOLING
200
°
C
150
°
C
100
°
C
50
°
C
TIME (3 TO 7 MINUTES TOTAL)
TMAX
SOLDER IS LIQUID FOR
40 TO 80 SECONDS
(DEPENDING ON
MASS OF ASSEMBLY)
205
°
TO 219
°
C
PEAK AT
SOLDER JOINT
DESIRED CURVE FOR LOW
MASS ASSEMBLIES
100
°
C
150
°
C
160
°
C
140
°
C
Figure 6. Typical Solder Heating Profile
DESIRED CURVE FOR HIGH
MASS ASSEMBLIES
170
°
C
For any given circuit board, there will be a group of
control settings that will give the desired heat pattern. The
operator must set temperatures for several heating zones,
and a figure for belt speed. Taken together, these control
settings make up a heating “profile” for that particular
circuit board. On machines controlled by a computer, the
computer remembers these profiles from one operating
session to the next. Figure 7 shows a typical heating profile
for use when soldering a surface mount device to a printed
circuit board. This profile will vary among soldering
systems but it is a good starting point. Factors that can
affect the profile include the type of soldering system in
use, density and types of components on the board, type of
solder used, and the type of board or substrate material
being used. This profile shows temperature versus time.
SOLDER STENCIL GUIDELINES
Prior to placing surface mount components onto a printed
circuit board, solder paste must be applied to the pads. A
solder stencil is required to screen the optimum amount of
solder paste onto the footprint. The stencil is made of brass
or stainless steel with a typical thickness of 0.008 inches.
The stencil opening size for the surface mounted package
should be the same as the pad size on the printed circuit
board, i.e., a 1:1 registration.
TYPICAL SOLDER HEATING PROFILE
The line on the graph shows the actual temperature that
might be experienced on the surface of a test board at or
near a central solder joint. The two profiles are based on a
high density and a low density board. The Vitronics
SMD310 convection/infrared reflow soldering system was
used to generate this profile. The type of solder used was
62/36/2 Tin Lead Silver with a melting point between
177–189
°
C. When this type of furnace is used for solder
reflow work, the circuit boards and solder joints tend to
heat first. The components on the board are then heated by
conduction. The circuit board, because it has a large surface
area, absorbs the thermal energy more efficiently, then
distributes this energy to the components. Because of this
effect, the main body of a component may be up to 30
degrees cooler than the adjacent solder joints.
相關PDF資料 |
PDF描述 |
|---|---|
| LV2210V | Basic Data Communication Receiver IC |
| LV23000 | Single-Chip Tuner IC for Radio/Cassette Players |
| LV23000M | Single-Chip Tuner IC for Radio/Cassette Players |
| LV23002M | Bi-CMOS IC For Radio Cassette and Mini Component System 1-chip Tuner IC Incorporating PLL |
| LV244 | OCTAL BUFFERS/DRIVERS WITH 3-STATE OUTPUTS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LV2209 | 制造商:ON Semiconductor 功能描述: |
| LV220M1CB-0513(E) | 制造商:SPC Multicomp 功能描述:CAPACITOR 22UF 16V |
| LV220M1EB-0513(E) | 制造商:SPC Multicomp 功能描述:CAPACITOR 22UF 25V |
| LV220M1JB-6.314(E) | 制造商:SPC Multicomp 功能描述:CAPACITOR 22UF 63V |
| LV220M1VB-0613(E) | 制造商:SPC Multicomp 功能描述:CAPACITOR 22UF 35V |
發布緊急采購，3分鐘左右您將得到回復。