參數資料
型號： LTM8062EV#PBF
廠商： LINEAR TECHNOLOGY CORP
元件分類： 穩壓器
英文描述： BATTERY CHARGE CONTROLLER, 1150 kHz SWITCHING FREQ-MAX, PBGA77
封裝： 15 X 9 MM, 4.32 MM HEIGHT, ROHS COMPLIANT, MO-222, LGA-77
文件頁數： 7/24頁
文件大小： 580K
代理商： LTM8062EV#PBF
LTM8062/LTM8062A
15
8062fa
APPLICATIONS INFORMATION
of the programmed charge current. The FAULT pin signals
bad-battery and NTC faults. These pins are binary coded,
as shown in Table 3.
Table 3. Status Pin State
CHRG
FAULT
STATUS
High
Not Charging—Standby or Shutdown Mode
High
Low
Bad-Battery Fault (Precondition Timeout/EOC Failure)
Low
High
Normal Charging at C/10 or Greater
Low
NTC Fault (Pause)
If the battery is removed from an LTM8062/LTM8062A
charger that is configured for C/10 termination, a low
amplitude sawtooth waveform appears at the charger
output, due to cycling between termination and recharge
events. This cycling results in pulsing at the CHRG output.
An LED connected to this pin will exhibit a blinking pat-
tern, indicating to the user that a battery is not present.
The frequency of this blinking pattern is dependent on the
output capacitance.
C/10 Charge Termination
The LTM8062/LTM8062A support a low current-based
termination scheme, where a battery charge cycle termi-
nates when the charge current falls below one-tenth the
programmed charge current, or approximately 200mA.
ThisterminationmodeisengagedbyshortingtheTMRpin
to ground. When C/10 termination is used, an LTM8062/
LTM8062A charger sources battery charge current as
long as the average current level remains above the C/10
threshold. As the full-charge float voltage is achieved, the
charge current falls until the C/10 threshold is reached,
at which time the charger terminates and the LTM8062/
LTM8062A enter standby mode. The CHRG status pin fol-
lows the charger cycle and is high impedance when the
charger is not actively charging. There is no provision for
bad-battery detection if C/10 termination is used.
Timer Charge Termination
The LTM8062/LTM8062A support a timer-based termina-
tion scheme, where a battery charge cycle terminates after
a specific amount of time elapses. Timer termination is
engaged when a capacitor (CTIMER) is connected from the
TMR pin to ground. The timer cycle time span (tEOC) is
determined by CTIMER in the equation:
CTIMER = tEOC 2.27 10–7 (Hours)
When charging at a 1C rate, tEOC is commonly set to three
hours, which requires a 0.68μF capacitor.
The CHRG status pin continues to signal charging, regard-
less of which termination scheme is used. When timer
termination is used, the CHRG status pin is pulled low
during a charge cycle until the charge current falls below
the C/10 threshold. The charger continues to top off the
battery until timer EOC, when the LTM8062/LTM8062A
terminate the charge cycle and enters standby mode.
Termination at the end of the timer cycle only occurs if the
charge cycle was successful. A successful charge cycle
occurs when the battery is charged to within 2.5% of the
full-charge float voltage. If a charge cycle is not success-
ful at EOC, the timer cycle resets and charging continues
for another full timer cycle. When VBAT drops 2.5% from
the full-charge float voltage, whether by battery loading
or replacement of the battery, the charger automatically
resets and starts charging.
Preconditioning and Bad-Battery Fault
TheLTM8062/LTM8062Ahaveapreconditionmode,where
the charge current is limited to 15% of the maximum
charge current, or approximately 300mA. Precondition
mode is engaged if the voltage on the BAT pin is below the
precondition threshold, or approximately 70% of the float
voltage. Once the BAT voltage rises above the precondition
threshold,normalfull-currentchargingcancommence.The
LTM8062/LTM8062Aincorporate90mVhysteresistoavoid
spurious mode transitions.
Bad-battery detection is engaged when the internal timer
is used for termination (capacitor tied to TMR). This fault
detection feature is designed to identify failed cells. A
bad-battery fault is triggered when the voltage on BAT
remains below the precondition threshold for greater
than one-eighth of a full timer cycle (one-eighth EOC). A
bad-battery fault is also triggered if a normally charging
batteryre-enterspreconditionmodeafterone-eighthEOC.
相關PDF資料
PDF描述
LTM8062AEV#PBF BATTERY CHARGE CONTROLLER, 1150 kHz SWITCHING FREQ-MAX, PBGA77
LTM9005CV-AA#PBF SPECIALTY ANALOG CIRCUIT, PBGA204
LTM9005CV-AB#PBF SPECIALTY ANALOG CIRCUIT, PBGA204
LTM9005IV-AB#PBF SPECIALTY ANALOG CIRCUIT, PBGA204
LUCW3000ACN-TR PLL FREQUENCY SYNTHESIZER, 2200 MHz, PDSO14
相關代理商/技術參數
參數描述
LTM8062IV#PBF 功能描述:IC BATTERY CHARGER TRACK 77-LGA RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:µModule® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR)
LTM8062IVPBF 制造商:LINER 制造商全稱:Linear Technology 功能描述:32VIN, 2A μModule Power Tracking Battery Charger
LTM-820 功能描述:LED 安裝硬件 LED Mount Self Ret 3 or 5mm Black RoHS:否 制造商:Bivar 產品:LED Mounting Clips LED 大小:5 mm 材料:Nylon 顏色:Black 主體長度:4.4 mm 面板厚度尺寸: 封裝:Bulk
LTM8328GKR04 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Optoelectronic
LTM-8328GKR-04 功能描述:LED 顯示器和配件 Green RoHS:否 制造商:Avago Technologies 顯示器類型:7 Segment 數位數量:2 字符大小:7.8 mm x 14.22 mm 照明顏色:Red 波長:628 nm 共用管腳:Common Anode 工作電壓:2.05 V 工作電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 35 C 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*