參數資料
型號： LTC4222CG#PBF
廠商： Linear Technology
文件頁數： 8/32頁
文件大小： 339K
描述： IC CTRLR DUAL HOT SWAP 36-SSOP
標準包裝： 37
類型： 熱交換控制器
應用： 通用
內部開關： 無
電源電壓： 2.9 V ~ 29 V
工作溫度： 0°C ~ 70°C
安裝類型： 表面貼裝
封裝/外殼： 36-SSOP（0.209"，5.30mm 寬）
供應商設備封裝： 36-SSOP
包裝： 管件
LTC4222
8
4222fb
PIN FUNCTIONS
ADIN: ADC Input. A voltage between 0 and 1.28V applied 
to this pin is measured by the on-board ADC. Tie to ground
if unused.
ADR0, ADR1, ADR2: Serial Bus Address Inputs. Tying 
these pins to ground, open, or INTV
CC
 configures one
of 27 possible addresses. See Table 1 in Applications
Information.
ALERT: Fault Alert Output. Open-drain logic output that 
is pulled to ground when a fault occurs to alert the host
controller. A fault alert is enabled by setting the corre-
sponding bit in the ALERT register as shown in Table 4.
See Applications Information. Tie to ground if unused.
CONFIG: Confguration Input. Confgures the part to control 
the two channels together or independently. When CONFIG
is tied to GND both channels start up at the same time. A
fault, EN or ON turn-off command on either channel will
shut down both channels. When CONFIG is tied to INTV
CC
,
either channel can start up independently. A fault, EN or
ON turn-off command will result in the associated chan-
nel turning off, while the other channel remains on. If one
channel is commanded to turn on while another channel is
in the turn-on sequence, the LTC4222 waits until the first
channel has finished its turn-on sequence before turning
on the second channel.
EN1, EN2: Enable Input. Ground this pin to indicate a 
board is present and enable the N-channel MOSFET to
turn-on. When this pin is high, the MOSFET is not allowed
to turn on. An internal 10礎 current source pulls up this
pin. Transitions on this pin are recorded in the FAULT
register. A high-to-low transition activates the logic to read
the state of the ON pin and clear faults. See Applications
Information.
EXPOSED PAD: (Pin 33, QFN Package) Exposed Pad. May 
be left open or connected to device ground.
FB1, FB2: Foldback Current Limit and Power-Good Input. 
A resistive divider from the output is tied to this pin. When
the voltage at this pin drops below 1.235V , power is not
considered good. The power bad condition may result
in the GPIO pin pulling low or going high impedance
depending on the configuration of CONTROL register
bits 6 and 7. Also a power bad fault is logged when the
FB pin is low, the LTC4222 has finished the startup cycle
and the GATE pin is high. See Applications Information.
The start-up current limit folds back from 50mV sense
voltage to 16.6mV as the FB voltage drops from 0.8V to
0.2V . Foldback is not active once the part leaves startup
and the current limit is increased to 150mV .
GATE1, GATE2: Gate Drive for External N-Channel MOSFET . 
An internal 12礎 current source charges the gate of the
MOSFET . No compensation capacitor is required on the
GATE pin, but a resistor and capacitor network from this
pin to ground may be used to set the turn-on output volt-
age slew rate. During turn-off there is a 1mA pull-down
current. During a short circuit or undervoltage lockout (V
DD
 
or INTV
CC
), a 450mA pull-down current source between
GATE and SOURCE is activated.
GND: Device Ground.
GPIO1, GPIO2: General Purpose Input/Output. Open-drain 
logic output or logic input. Defaults to an output set to pull
low to indicate power is not good. Configure according
to Table 3.
INTV
CC
: Low Voltage Supply Decoupling Output. Connect 
a 0.1礔 capacitor from this pin to ground.
ON: (QFN Package) On Control Input. Formed by internally 
tying the ON1 and ON2 lines together.
ON1, ON2: (SSOP Package) On Control Inputs. A rising 
edge turns on the external N-channel FET and a falling edge
turns it off. This pin also configures the state of the FET
ON register bit (and hence the external FET) at power up.
For example, if the ON pin is tied high, then the FET ON bit
(Control bit 3 in Table 3) goes high 100ms after power-up.
Likewise if the ON pin is tied low then the channel remains
off after power-up until the FET ON bit is set high using
the I
2
C bus. A high-to-low transition on this pin clears the
fault register for the related channel. The two ON pins are
tied together internally on the QFN package.
OV1, OV2: Overvoltage Comparator Input. Connect this pin 
to an external resistive divider from V
DD
. If the voltage at
this pin rises above 1.235V , an overvoltage fault is detected
and the GATE turns off. Tie to GND if unused.
相關PDF資料
PDF描述
LTC4223CDHD-2#PBF IC CNTRLR HOT SWAP DUAL 16-DFN
LTC4224IDDB-2#TRPBF IC CNTRLR HOT SWAP DUAL 10-DFN
LTC4225IGN-1#PBF IC CONTROLLER HOT SWAP 24-SSOP
LTC4230CGN#TRPBF IC CONTRLLR HOT SWAP TRPL 20SSOP
LTC4232CDHC#TRPBF IC CTLR HOT SWAP 5A 16-DFN
相關代理商/技術參數
參數描述
LTC4222CG-TRPBF 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual Hot Swap Controller with I2C Compatible Monitoring
LTC4222CUH#PBF 功能描述:IC CTRLR DUAL HOT SWAP 32-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF)
LTC4222CUH#TRPBF 功能描述:IC CTRLR DUAL HOT SWAP 32-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF)
LTC4222CUH-PBF 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual Hot Swap Controller with I2C Compatible Monitoring
LTC4222CUH-TRPBF 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual Hot Swap Controller with I2C Compatible Monitoring
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*