- 您現在的位置：買賣IC網 > PDF目錄30771 > LTC4000IUFD#TRPBF (LINEAR TECHNOLOGY CORP) 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PQCC28 PDF資料下載
參數資料
| 型號： | LTC4000IUFD#TRPBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PQCC28 |
| 封裝： | 4 X 5 MM, LEAD FREE, PLASTIC, MO-220WXXX-X, QFN-28 |
| 文件頁數： | 7/40頁 |
| 文件大?。?/td> | 428K |
| 代理商： | LTC4000IUFD#TRPBF |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
LTC4000
15
4000f
operaTion
Charge Current Regulation
The first loop involved in a normal charging cycle is the
charge current regulation loop (Figure 3). As with the input
current regulation loop, this loop also drives the ITH and
CC pins. This loop ensures that the charge current sensed
through the charge current sense resistor (RCS) does not
exceed the programmed full charge current.
Battery Instant-On and Ideal Diode
The LTC4000 controls the external PMOS connected to the
BGATE pin with a controller similar to the input ideal diode
controller driving the IGATE pin. When not charging, the
PMOS behaves as an ideal diode between the BAT (anode)
and the CSN (cathode) pins. The controller (A2) regulates
the external PMOS to achieve low loss conduction by driv-
ing the gate of the PMOS device such that the voltage drop
from the BAT pin to the CSN pin is 8mV. When the ability
to deliver a particular current with an 8mV drop across
the PMOS source and drain is exceeded, the voltage at
the gate clamps at VBGATE(ON) and the PMOS behaves like
a fixed value resistor (RDS(ON)).
The ideal diode behavior allows the battery to provide cur-
rent to the load when the input supply is in current limit
or the DC/DC converter is slow to react to an immediate
load increase at the output. In addition to the ideal diode
behavior, BGATE also allows current to flow from the CSN
pin to the BAT pin during charging.
There are two regions of operation when current is flowing
from the CSN pin to the BAT pin. The first is when charg-
ing into a battery whose voltage is below the instant-on
threshold (VOFB < VOUT(INST_ON)). In this region of opera-
tion, the controller regulates the voltage at the CSP pin
Figure 3. Charge Current Regulation Loop
Figure 4. Battery Float Voltage Regulation Loop with FBG
Figure 5. Output Voltage Regulation Loop with FBG
CSP
CC
1V
A5
ITH
LTC4000
CSP
CSN
RIS
BAT PMOS
TO SYSTEM
IBMON
CL
CIBMON
(OPTIONAL)
CCSP
+
–
+
–
CC
TO DC/DC
4000 FO3
RC
60k
50A AT NORMAL
5A AT TRICKLE
BIAS
A9
gm = 0.33m
RCL
CC
1.136V
ITH
LTC4000
BFB
BAT
FBG
–
+
CC
TO DC/DC
4000 FO4
RC
RBFB2
RBFB1
A6
+
–
CC
1.193V
ITH
LTC4000
OFB
CSP
FBG
–
+
CC
TO DC/DC
4000 FO5
RC
ROFB2
ROFB1
A7
+
–
Battery Voltage Regulation
Once the float voltage is reached, the battery voltage regu-
lation loop takes over from the charge current regulation
loop (Figure 4).
The float voltage level is programmed using the feedback
resistor divider between the BAT pin and the FBG pin with
the center node connected to the BFB pin. Note that the
ground return of the resistor divider is connected to the
FBG pin. The FBG pin disconnects the resistor divider
load when VIN < 3V to ensure that the float voltage resis-
tor divider does not consume battery current when the
battery is the only available power source. For VIN ≥ 3V,
the typical resistance from the FBG pin to GND is 100Ω.
Output Voltage Regulation
When charging terminates and the system load is com-
pletely supplied from the input, the PMOS connected to
BGATE is turned off. In this scenario, the output voltage
regulation loop takes over from the battery float voltage
regulation loop (Figure 5). The output voltage regulation
loop regulates the voltage at the CSP pin such that the
output feedback voltage at the OFB pin is 1.193V.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4075XEDD | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
| LTC4075XEDD#PBF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
| LTC4095EDC#TR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| LTC4095EDC | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| LTC4095EDC#TRM | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4001 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:2A Synchronous Buck Li-Ion Charger |
| LTC4001-1 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:2A Synchronous Buck Li-Ion Charger |
| LTC4001EUF | 制造商:Linear Technology 功能描述:Battery Charger Li-Ion/Li-Pol 2000mA 4.2V 16-Pin QFN EP |
| LTC4001EUF#PBF | 功能描述:IC CHARGER LI-ION BUCK 16-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 其它有關文件:STC3100 View All Specifications 特色產品:STC3100 - Battery Monitor IC 標準包裝:4,000 系列:- 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MiniSO 包裝:帶卷 (TR) 其它名稱:497-10526-2 |
| LTC4001EUF#TRPBF | 功能描述:IC CHARGER LI-ION BUCK 16-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:61 系列:- 功能:電源管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:4.35 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:22-WFDFN 裸露焊盤 供應商設備封裝:22-DFN（6x3）裸露焊盤 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。