- 您現在的位置：買賣IC網 > PDF目錄44993 > LTC3810IG#TR (LINEAR TECHNOLOGY CORP) SWITCHING CONTROLLER, PDSO28 PDF資料下載
參數資料
| 型號： | LTC3810IG#TR |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | SWITCHING CONTROLLER, PDSO28 |
| 封裝： | 5.30 MM, PLASTIC, SSOP-28 |
| 文件頁數： | 21/36頁 |
| 文件大?。?/td> | 495K |
| 代理商： | LTC3810IG#TR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
LTC3810
28
3810fb
voltage VOUT2(MIN) below which continuous operation is
forced until VOUT2 has risen above its minimum.
VOUT2(MIN) = 0.8V 1+
R4
R3
lies the same percentage below the typical value as the
maximum lies above it. Consult the MOSFET manufacturer
for further guidelines.
To further limit current in the event of a short-circuit to
ground, the LTC3810 includes foldback current limiting.
If the output falls by more than 60%, then the maximum
sense voltage is progressively lowered to about one tenth
of its full value.
Be aware also that when the fault timeout is enabled for
the external NMOS regulator, an over current limit may
cause the output to fall below the minimum 6.5V UV
threshold. This condition will cause a linear regulator
timeout/restart sequence as described in the Linear Regula-
tor Timeout section if this condition persists.
Soft-Start and Tracking
The LTC3810 has the ability to either soft-start by itself with
a capacitor or track the output of another supply. When
the device is congured to soft-start by itself, a capacitor
should be connected to the TRACK/SS pin. The LTC3810 is
put in a low quiescent current shutdown state (IQ ~240μA)
if the SHDN pin voltage is below 1.5V. The TRACK/SS
pin is actively pulled to ground in this shutdown state.
Once the SHDN pin voltage is above 1.5V, the LTC3810 is
powered up. A soft-start current of 1.4μA then starts to
charge the soft-start capacitor CSS. Note that soft-start
is achieved not by limiting the maximum output current
of the controller but by controlling the ramp rate of the
output voltage. Current foldback is disabled during this
soft-start phase. During the soft-start phase, the LTC3810
is ramping the reference voltage until it reaches 0.8V. The
force continuous mode is also disabled and PGOOD signal
is forced low during this phase. The total soft-start time
can be calculated as:
tSOFTSTART = 0.8 CSS/1.4μA
When the device is congured to track another supply,
the feedback voltage of the other supply is duplicated
by a resistor divider and applied to the TRACK/SS pin.
Therefore, the voltage ramp rate on this pin is determined
by the ramp rate of the other supply output voltage.
Table 1.
MODE/SYNC PIN
CONDITION
DC Voltage: 0V to 0.75V
Forced Continuous
Current Reversal Enabled
DC Voltage: ≥ 0.85V
Pulse Skip Mode Operation
No Current Reversal
Feedback Resistors
Regulating a Secondary Winding
Ext. Clock OV to ≥ 2V
Forced Continuous
Current Reversal Enabled
Fault Conditions: Current Limit and Foldback
The maximum inductor current is inherently limited in a
current mode controller by the maximum sense voltage.
In the LTC3810, the maximum sense voltage is controlled
by the voltage on the VRNG pin. With valley current control,
the maximum sense voltage and the sense resistance
determine the maximum allowed inductor valley current.
The corresponding output current limit is:
ILIMIT =
VSNS(MAX)
RDS(ON) T
+
1
2
IL
The current limit value should be checked to ensure that
ILIMIT(MIN) > IOUT(MAX). The minimum value of current limit
generally occurs with the largest VIN at the highest ambi-
ent temperature, conditions that cause the largest power
loss in the converter. Note that it is important to check for
self-consistency between the assumed MOSFET junction
temperature and the resulting value of ILIMIT which heats
the MOSFET switches.
Caution should be used when setting the current limit
based upon the RDS(ON) of the MOSFETs. The maximum
current limit is determined by the minimum MOSFET
on-resistance. Data sheets typically specify nominal
and maximum values for RDS(ON), but not a minimum.
A reasonable assumption is that the minimum RDS(ON)
APPLICATIONS INFORMATION
相關PDF資料 |
PDF描述 |
|---|---|
| LTC3810EG | SWITCHING CONTROLLER, PDSO28 |
| LTC3812EFE-5 | 1 A SWITCHING CONTROLLER, PDSO16 |
| LTC3812IFE-5#TR | 1 A SWITCHING CONTROLLER, PDSO16 |
| LTC3812EFE-5#TR | 1 A SWITCHING CONTROLLER, PDSO16 |
| LTC3812IFE-5 | 1 A SWITCHING CONTROLLER, PDSO16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC3810IUH-5#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 32-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR) |
| LTC3810IUH-5#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 32-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR) |
| LTC3811EG#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 36-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:PolyPhase® 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR) |
| LTC3811EG#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 36-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:PolyPhase® 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR) |
| LTC3811EUHF#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 38-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:PolyPhase® 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。