- 您現在的位置：買賣IC網 > PDF目錄44992 > LTC3672BEDC-2#PBF (LINEAR TECHNOLOGY CORP) 1.1 A SWITCHING REGULATOR, 2700 kHz SWITCHING FREQ-MAX, PDSO8 PDF資料下載
參數資料
| 型號： | LTC3672BEDC-2#PBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 1.1 A SWITCHING REGULATOR, 2700 kHz SWITCHING FREQ-MAX, PDSO8 |
| 封裝： | 2 X 2 MM, 0.75 MM HEIGHT, LEAD FREE, PLASTIC, DFN-8 |
| 文件頁數： | 10/12頁 |
| 文件大小： | 165K |
| 代理商： | LTC3672BEDC-2#PBF |
LTC3672B-2
7
3672b2fa
OPERATION
INTRODUCTION
The LTC3672B-2 combines a synchronous buck converter
with two low dropout linear DC regulators (LDOs) to
provide three low voltage outputs from a higher voltage
input source. All outputs are enabled and disabled together
through the ENALL pin. The output regulation voltages are
set during manufacturing to 1.2V nominal for the buck,
2.8V nominal for LDO1, and 1.8V nominal for LDO2.
For versions of the IC with different output regulation
voltages, consult the LTC factory.
SYNCHRONOUS BUCK REGULATOR
The synchronous buck uses a constant-frequency current
mode architecture, switching at 2.25MHz down to very light
loads, and supports no-load operation by skipping cycles.
When the input voltage drops very close to or falls below
the target output voltage, the buck supports 100% duty
cycle operation (low dropout mode). Soft-start circuitry
limits inrush current when powering on. Output current is
limited in the event of an output short-circuit. The switch
node is slew-rate limited to reduce EMI radiation. The
buck regulation control-loop compensation is internal to
the IC, and requires no external components.
Main Control Loop
An error amplier monitors the difference between an
internal reference voltage and the voltage on the BUCKOUT
pin. When the BUCKOUT voltage is below the reference,
the error amplier output voltage increases. When the
BUCKOUT voltage exceeds the reference, the error ampli-
er output voltage decreases.
The error amplier output controls the peak inductor current
through the following mechanism: Paced by a free-running
2.25MHz oscillator, the main P-channel MOSFET switch is
turned on at the start of the oscillator cycle. Current ows
from the VIN supply through this PMOS switch, through
the inductor via the SW pin, and into the output capacitor
and load. When the current reaches the level programmed
by the output of the error amplier, the PMOS is shut off,
and the N-channel MOSFET synchronous rectier turns
on. Energy stored in the inductor discharges into the load
through this NMOS. The NMOS turns off at the end of the
2.25MHz cycle, or sooner, if the current through it drops
to zero before the end of the cycle.
Through these mechanisms, the error amplier adjusts the
peak inductor current to deliver the required output power
to regulate the output voltage as sensed by the BUCKOUT
pin. All necessary control-loop compensation is internal to
the step-down switching regulator, requiring only a single
ceramic output capacitor for stability.
Light Load/No-Load Cycle-Skipping
At light loads, the inductor current may reach zero before
the end of the oscillator cycle, which will turn off the NMOS
synchronous rectier. In this case, the SW pin goes high
impedance and will show damped “ringing”. This is known
as discontinuous operation, and is normal behavior for a
switching regulator. At very light load and no-load condi-
tions, the buck will automatically skip cycles as needed
to maintain output regulation.
Soft-Start
Soft-start in the buck regulator is accomplished by gradually
increasing the maximum allowed peak inductor current
over a 200μs period. This allows the output to rise slowly,
controlling the inrush current required to charge up the
output capacitor. A soft-start cycle occurs whenever the
LTC3672B-2 is enabled, or after a fault condition has oc-
curred (thermal shutdown or UVLO).
相關PDF資料 |
PDF描述 |
|---|---|
| LTC3707IGN-SYNC | 3 A SWITCHING CONTROLLER, 360 kHz SWITCHING FREQ-MAX, PDSO28 |
| LTC3728IUH | 3 A DUAL SWITCHING CONTROLLER, 590 kHz SWITCHING FREQ-MAX, PQCC32 |
| LTC3728IG | 3 A DUAL SWITCHING CONTROLLER, 590 kHz SWITCHING FREQ-MAX, PDSO28 |
| LTC3728LIUH-1#TR | 3 A DUAL SWITCHING CONTROLLER, 590 kHz SWITCHING FREQ-MAX, PQCC32 |
| LTC3728LIGN-1 | 3 A DUAL SWITCHING CONTROLLER, 590 kHz SWITCHING FREQ-MAX, PDSO28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC3675EUFF#PBF | 功能描述:IC PMIC PWR SUPPLYED DVR 44-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 標準包裝:1 系列:- 應用:手持/移動設備 電流 - 電源:- 電源電壓:3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-LLP-EP（4x4） 包裝:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名稱:LP3905SD-30DKR |
| LTC3675EUFF#TRPBF | 功能描述:IC PMIC PWR SUPPLYED DVR 44-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 標準包裝:1 系列:- 應用:手持/移動設備 電流 - 電源:- 電源電壓:3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-LLP-EP（4x4） 包裝:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名稱:LP3905SD-30DKR |
| LTC3675EUFF-1#PBF | 制造商:Linear Technology 功能描述:MISC 制造商:Linear Technology 功能描述:IC PWR SUPPLY + LED DRVR 44QFN 制造商:Linear Technology 功能描述:DP-PMIC Multifunction, 8-Channel Configurable High Power PMIC |
| LTC3675EUFF-1#TRPBF | 制造商:Linear Technology 功能描述:7-CHANNEL CONFI GURABLE HIGH POWER PMIC 制造商:Linear Technology 功能描述:IC PWR SUPPLY + LED DRVR 44QFN 制造商:Linear Technology 功能描述:DP-PMIC Multifunction, 8-Channel Configurable High Power PMIC |
| LTC3676EUJ#PBF | 制造商:Linear Technology 功能描述: 制造商:Linear Technology 功能描述:DP-PMIC Multifunction, PMIC For Applications Processors |
發布緊急采購，3分鐘左右您將得到回復。