- 您現在的位置：買賣IC網 > PDF目錄98003 > LTC3559EUD (LINEAR TECHNOLOGY CORP) 1.05 A BATTERY CHARGE CONTROLLER, 2590 kHz SWITCHING FREQ-MAX, PQCC16 PDF資料下載
參數資料
| 型號： | LTC3559EUD |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 1.05 A BATTERY CHARGE CONTROLLER, 2590 kHz SWITCHING FREQ-MAX, PQCC16 |
| 封裝： | 3 X 3 MM, PLASTIC, MO-220WEED-2, QFN-16 |
| 文件頁數： | 4/24頁 |
| 文件大?。?/td> | 302K |
| 代理商： | LTC3559EUD |
LTC3559
12
3559f
APPLICATIONS INFORMATION
Suspend Mode
The battery charger can also be disabled by pulling the
SUSP pin above 1.2V. In suspend mode, the battery
drain current is reduced to 1.5μA and the input current is
reduced to 8.5μA.
Charge Cycle Overview
When a battery charge cycle begins, the battery charger
rst determines if the battery is deeply discharged. If the
battery voltage is below VTRKL, typically 2.9V, an automatic
trickle charge feature sets the battery charge current to
10% of the full-scale value.
Once the battery voltage is above 2.9V, the battery char-
ger begins charging in constant current mode. When the
battery voltage approaches the 4.2V required to maintain
a full charge, otherwise known as the oat voltage, the
charge current begins to decrease as the battery charger
switches into constant voltage mode.
Trickle Charge and Defective Battery Detection
Any time the battery voltage is below VTRKL, the charger
goes into trickle charge mode and reduces the charge
current to 10% of the full-scale current. If the battery
voltage remains below VTRKL for more than 1/2 hour, the
charger latches the bad-battery state, automatically termi-
nates, and indicates via the
CHRG pin that the battery was
unresponsive. If for any reason the battery voltage rises
above VTRKL, the charger will resume charging. Since the
charger has latched the bad-battery state, if the battery
voltage then falls below VTRKL again but without rising past
VRECHRG rst, the charger will immediately assume that
the battery is defective. To reset the charger (i.e., when
the dead battery is replaced with a new battery), simply
remove the input voltage and reapply it or put the part in
and out of suspend mode.
Charge Termination
The battery charger has a built-in safety timer that sets
the total charge time for 4 hours. Once the battery volt-
age rises above VRECHRG (typically 4.1V) and the charger
enters constant voltage mode, the 4-hour timer is started.
After the safety timer expires, charging of the battery will
discontinue and no more current will be delivered.
Automatic Recharge
After the battery charger terminates, it will remain off,
drawing only microamperes of current from the battery.
If the portable product remains in this state long enough,
the battery will eventually self discharge. To ensure that
the battery is always topped off, a charge cycle will au-
tomatically begin when the battery voltage falls below
VRECHRG (typically 4.1V). In the event that the safety timer
is running when the battery voltage falls below VRECHRG, it
will reset back to zero. To prevent brief excursions below
VRECHRG from resetting the safety timer, the battery voltage
must be below VRECHRG for more than 1.7ms. The charge
cycle and safety timer will also restart if the VCC UVLO or
DUVLO cycles low and then high (e.g., VCC is removed
and then replaced) or the charger enters and then exits
suspend mode.
Programming Charge Current
The PROG pin serves both as a charge current program
pin, and as a charge current monitor pin. By design, the
PROG pin current is 1/800th of the battery charge current.
Therefore, connecting a resistor from PROG to ground
programs the charge current while measuring the PROG pin
voltage allows the user to calculate the charge current.
Full-scale charge current is dened as 100% of the constant
current mode charge current programmed by the PROG
resistor. In constant current mode, the PROG pin servos to
1V if HPWR is high, which corresponds to charging at the
full-scale charge current, or 200mV if HPWR is low, which
corresponds to charging at 20% of the full-scale charge
current. Thus, the full-scale charge current and desired
program resistor for a given full-scale charge current are
calculated using the following equations:
I
V
R
V
I
CHG
PROG
CHG
=
800
相關PDF資料 |
PDF描述 |
|---|---|
| LTC3586EUFE#PBF | 3 A BATTERY CHARGE CONTROLLER, 2700 kHz SWITCHING FREQ-MAX, PQCC38 |
| LTC3586EUFE-1#PBF | BATTERY CHARGE CONTROLLER, PQCC38 |
| LTC3586EUFE-1#TRPBF | BATTERY CHARGE CONTROLLER, PQCC38 |
| LTC3672BEDC-1#PBF | 1.1 A SWITCHING REGULATOR, 2700 kHz SWITCHING FREQ-MAX, PDSO8 |
| LTC3728LZEUH | 3 A DUAL SWITCHING CONTROLLER, 590 kHz SWITCHING FREQ-MAX, PQCC28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC3559EUD#PBF | 功能描述:IC USB CHARGER 16-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 其它有關文件:STC3100 View All Specifications 特色產品:STC3100 - Battery Monitor IC 標準包裝:4,000 系列:- 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MiniSO 包裝:帶卷 (TR) 其它名稱:497-10526-2 |
| LTC3559EUD#PBF | 制造商:Linear Technology 功能描述:IC BATT CHARGER W/BUCK REG 16QFN 制造商:Linear Technology 功能描述:IC, BATT CHARGER, W/BUCK REG, 16QFN |
| LTC3559EUD#TRPBF | 功能描述:IC USB CHARGER 16-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:61 系列:- 功能:電源管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:4.35 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:22-WFDFN 裸露焊盤 供應商設備封裝:22-DFN（6x3）裸露焊盤 包裝:管件 |
| LTC3559EUD-1#PBF | 功能描述:IC USB BATTERY CHARGER 16-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:61 系列:- 功能:電源管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:4.35 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:22-WFDFN 裸露焊盤 供應商設備封裝:22-DFN（6x3）裸露焊盤 包裝:管件 |
| LTC3559EUD-1#TRPBF | 功能描述:IC USB BATTERY CHARGER 16-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:61 系列:- 功能:電源管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:4.35 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:22-WFDFN 裸露焊盤 供應商設備封裝:22-DFN（6x3）裸露焊盤 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。