- 您現在的位置：買賣IC網 > PDF目錄98003 > LTC3559EUD (LINEAR TECHNOLOGY CORP) 1.05 A BATTERY CHARGE CONTROLLER, 2590 kHz SWITCHING FREQ-MAX, PQCC16 PDF資料下載
參數資料
| 型號： | LTC3559EUD |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 1.05 A BATTERY CHARGE CONTROLLER, 2590 kHz SWITCHING FREQ-MAX, PQCC16 |
| 封裝： | 3 X 3 MM, PLASTIC, MO-220WEED-2, QFN-16 |
| 文件頁數： | 24/24頁 |
| 文件大?。?/td> | 302K |
| 代理商： | LTC3559EUD |
LTC3559
9
3559f
GND (Pin1): Ground, Connect to Exposed Pad (Pin 17).
BAT (Pin 2): Charge Current Output. Provides charge cur-
rent to the battery and regulates nal oat voltage to 4.2V.
MODE (Pin 3): MODE Pin for Buck Regulators. When held
high, both regulators are in Burst Mode operation. When
held low both regulators operate in pulse skip mode. This
pin is a high impedance input; do not oat.
FB1 (Pin 4): Buck 1 Feedback Voltage Pin. Receives feed-
back by a resistor divider connected across the output.
EN1 (Pin 5): Enable Input Pin for Buck 1. This pin is a high
impedance input; do not oat. Active high.
SW1 (Pin 6): Buck 1 Switching Node. External inductor
connects to this node.
PVIN (Pin 7): Input Supply Pin for Buck Regulators.
Connect to BAT. A 2.2
μF decoupling capacitor to GND is
recommended.
SW2 (Pin 8): Buck 2 Switching Node. External inductor
connects to this node.
EN2 (Pin 9): Enable Input Pin for Buck 2. This pin is a high
impedance input; do not oat. Active high.
FB2 (Pin 10): Buck 2 Feedback Voltage Pin. Receives feed-
back by a resistor divider connected across the output.
SUSP (Pin 11): Suspend Battery Charging Operation.
A voltage greater than 1.2V on this pin puts the battery
charger into suspend mode, disables the charger and
resets the termination timer. A weak pull-down current is
internally applied to this pin to ensure it is low at power
up when the input is not being driven externally.
HPWR (Pin 12): High Current Battery Charging Enabled.
A voltage greater than 1.2V at this pin programs the
BAT pin current at 100% of the maximum programmed
charge current. A voltage less than 0.4V sets the BAT pin
current to 20% of the maximum programmed charge
current. When used with a 1.74k PROG resistor, this pin
can toggle between low power and high power modes per
USB specication. A weak pull-down current is internally
applied to this pin to ensure it is low at power up when
the input is not being driven externally.
NTC (Pin 13): Input to the NTC Thermistor Monitoring
Circuit. The NTC pin connects to a negative temperature
coefcient thermistor which is typically co-packaged with
the battery pack to determine if the battery is too hot or
too cold to charge. If the battery temperature is out of
range, charging is paused until the battery temperature
re-enters the valid range. A low drift bias resistor is re-
quired from VCC to NTC and a thermistor is required from
NTC to ground. To disable the NTC function, the NTC pin
should be grounded.
PROG (Pin 14): Charge Current Program and Charge
Current Monitor Pin. Charge current is programmed by
connecting a resistor from PROG to ground. When charging
in constant current mode, the PROG pin servos to 1V if
the HPWR pin is pulled high, or 200mV if the HPWR pin
is pulled low. The voltage on this pin always represents
the battery current through the following formula:
I
PROG
R
BAT
PROG
=
800
CHRG (Pin 15): Open-Drain Charge Status Output. The
CHRG pin indicates the status of the battery charger. Four
possible states are represented by
CHRG: charging, not
charging (i.e., the charge current is less than 1/10th of the
full-scale charge current), unresponsive battery (i.e., the
battery voltage remains below 2.9V after 1/2 hour of charg-
ing) and battery temperature out of range.
CHRG requires
a pull-up resistor and/or LED to provide indication.
VCC (Pin 16): Battery Charger Input. A 1μF decoupling
capacitor to GND is recommended.
Exposed Pad (Pin 17): Ground. The Exposed Pad must
be soldered to PCB ground to provide electrical contact
and rated thermal performance.
PIN FUNCTIONS
相關PDF資料 |
PDF描述 |
|---|---|
| LTC3586EUFE#PBF | 3 A BATTERY CHARGE CONTROLLER, 2700 kHz SWITCHING FREQ-MAX, PQCC38 |
| LTC3586EUFE-1#PBF | BATTERY CHARGE CONTROLLER, PQCC38 |
| LTC3586EUFE-1#TRPBF | BATTERY CHARGE CONTROLLER, PQCC38 |
| LTC3672BEDC-1#PBF | 1.1 A SWITCHING REGULATOR, 2700 kHz SWITCHING FREQ-MAX, PDSO8 |
| LTC3728LZEUH | 3 A DUAL SWITCHING CONTROLLER, 590 kHz SWITCHING FREQ-MAX, PQCC28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC3559EUD#PBF | 功能描述:IC USB CHARGER 16-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 其它有關文件:STC3100 View All Specifications 特色產品:STC3100 - Battery Monitor IC 標準包裝:4,000 系列:- 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MiniSO 包裝:帶卷 (TR) 其它名稱:497-10526-2 |
| LTC3559EUD#PBF | 制造商:Linear Technology 功能描述:IC BATT CHARGER W/BUCK REG 16QFN 制造商:Linear Technology 功能描述:IC, BATT CHARGER, W/BUCK REG, 16QFN |
| LTC3559EUD#TRPBF | 功能描述:IC USB CHARGER 16-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:61 系列:- 功能:電源管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:4.35 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:22-WFDFN 裸露焊盤 供應商設備封裝:22-DFN（6x3）裸露焊盤 包裝:管件 |
| LTC3559EUD-1#PBF | 功能描述:IC USB BATTERY CHARGER 16-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:61 系列:- 功能:電源管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:4.35 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:22-WFDFN 裸露焊盤 供應商設備封裝:22-DFN（6x3）裸露焊盤 包裝:管件 |
| LTC3559EUD-1#TRPBF | 功能描述:IC USB BATTERY CHARGER 16-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:61 系列:- 功能:電源管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:4.35 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:22-WFDFN 裸露焊盤 供應商設備封裝:22-DFN（6x3）裸露焊盤 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。