參數資料
型號： LTC3542IS6#PBF
廠商： LINEAR TECHNOLOGY CORP
元件分類： 穩壓器
英文描述： SWITCHING REGULATOR, 2700 kHz SWITCHING FREQ-MAX, PDSO6
封裝： LEAD FREE, PLASTIC, MO-193, TSOT-23, 6 PIN
文件頁數： 14/16頁
文件大?。?/td> 211K
代理商： LTC3542IS6#PBF
LTC3542
7
3542fa
The LTC3542 uses a constant frequency, current mode,
step-down architecture. The operating frequency is set at
2.25MHz and can be synchronized to an external oscillator.
To suit a variety of applications, the selectable MODE/SYNC
pin allows the user to trade-off noise for efciency.
The output voltage is set by an external divider returned
to the VFB pin. An error amplier compares the divided
output voltage with a reference voltage of 0.6V and adjusts
the peak inductor current accordingly.
Main Control Loop
During normal operation, the top power switch (P-channel
MOSFET) is turned on at the beginning of a clock cycle
when the VFB voltage is below the reference voltage. The
current ows into the inductor and the load increases until
the current limit is reached. The switch turns off and energy
stored in the inductor ows through the bottom switch
(N-channel MOSFET) into the load until the next clock cycle.
The peak inductor current is controlled by the internally
compensated output of the error amplier. When the load
current increases, the VFB voltage decreases slightly below
the reference. This decrease causes the error amplier to
increase its output voltage until the average inductor cur-
rent matches the new load current. The main control loop
is shut down by pulling the RUN pin to ground.
Low Load Current Operation
By selecting MODE/SYNC pin, two modes are available to
control the operation of the LTC3542 at low load currents.
Both modes automatically switch from continuous opera-
tion to the selected mode when the load current is low.
To optimize efciency, the Burst Mode operation can be
selected. When the converter is in Burst Mode operation,
the peak current of the inductor is set to approximately
60mA regardless of the output load. Each burst event can
last from a few cycles at light loads to almost continuously
cycling with short sleep intervals at moderate loads. In
between these burst events, the power MOSFETs and any
unneeded circuitry are turned off, reducing the quiescent
current to 26μA. In this sleep state, the load current is
being supplied solely from the output capacitor. As the
output voltage drops, the EA amplier’s output rises above
the sleep threshold and turns the top MOSFET on. This
process repeats at a rate that is dependent on the load
demand. By running cycles periodically, the switching
losses which are dominated by the gate charge losses of
the power MOSFETs are minimized.
For lower ripple noise at low load currents, the pulse skip
mode can be used. In this mode, the regulator continues
to switch at a constant frequency down to very low load
currents, where it will begin skipping pulses.
Dropout Operation
When the input supply voltage decreases toward the output
voltage, the duty cycle increases to 100%, which is the
dropout condition. In dropout, the PMOS switch is turned
on continuously with the output voltage being equal to the
input voltage minus the voltage drops across the internal
P-channel MOSFET and the inductor. An important design
consideration is that the RDS(ON) of the P-channel switch
increases with decreasing input supply voltage (See Typical
Performance Characteristics). Therefore, the user should
calculate the power dissipation when the LTC3542 is used
at 100% duty cycle with low input voltage (See Thermal
Considerations in the Applications Information Section).
Low Supply Operation
To prevent unstable operation, the LTC3542 incorporates
an undervoltage lockout circuit which shuts down the part
when the input voltage drops below about 2V.
Internal Soft-Start
At start-up when the RUN pin is brought high, the internal
reference is linearly ramped from 0V to 0.6V in about 1ms.
The regulated feedback voltage follows this ramp resulting
in the output voltage ramping from 0% to 100% in 1ms.
The current in the inductor during soft-start is dened
by the combination of the current needed to charge the
output capacitance and the current provided to the load
as the output voltage ramps up. The start-up waveform,
shown in the Typical Performance Characteristics, shows
the output voltage start-up from 0V to 1.8V with a 500mA
load and VIN = 3.6V (refer to Figure 3a).
OPERATION
相關PDF資料
PDF描述
LTC3559EUD 1.05 A BATTERY CHARGE CONTROLLER, 2590 kHz SWITCHING FREQ-MAX, PQCC16
LTC3586EUFE#PBF 3 A BATTERY CHARGE CONTROLLER, 2700 kHz SWITCHING FREQ-MAX, PQCC38
LTC3586EUFE-1#PBF BATTERY CHARGE CONTROLLER, PQCC38
LTC3586EUFE-1#TRPBF BATTERY CHARGE CONTROLLER, PQCC38
LTC3672BEDC-1#PBF 1.1 A SWITCHING REGULATOR, 2700 kHz SWITCHING FREQ-MAX, PDSO8
相關代理商/技術參數
參數描述
LTC3542IS6-TRPBF 制造商:LINER 制造商全稱:Linear Technology 功能描述:500mA, 2.25MHz Synchronous Step-Down DC/DC Converter
LTC3543 制造商:LINER 制造商全稱:Linear Technology 功能描述:600mA Synchronous Step Down Buck Regulator with PLL, Soft-Start and Spread Spectrum
LTC3543EDCB 制造商:LINER 制造商全稱:Linear Technology 功能描述:600mA Synchronous Step Down Buck Regulator with PLL, Soft-Start and Spread Spectrum
LTC3543EDCB#PBF 制造商:Linear Technology 功能描述:REG STEP DOWN 0.6A SMD DFN-6 制造商:Linear Technology 功能描述:REG, STEP DOWN, 0.6A, SMD, DFN-6
LTC3543EDCB#TRMPBF 功能描述:IC REG BUCK SYNC ADJ 0.6A 8DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:升壓（升壓） 輸出類型:可調式 輸出數:1 輸出電壓:1.24 V ~ 30 V 輸入電壓:1.5 V ~ 12 V PWM 型:電流模式，混合 頻率 - 開關:600kHz 電流 - 輸出:500mA 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) 供應商設備封裝:8-SOIC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*