- 您現在的位置：買賣IC網 > PDF目錄44991 > LTC3533EDE#TR (LINEAR TECHNOLOGY CORP) 7 A SWITCHING REGULATOR, 2000 kHz SWITCHING FREQ-MAX, PDSO14 PDF資料下載
參數資料
| 型號： | LTC3533EDE#TR |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 7 A SWITCHING REGULATOR, 2000 kHz SWITCHING FREQ-MAX, PDSO14 |
| 封裝： | 4 X 3 MM, 0.75 MM HEIGHT, PLASTIC, MO-229WGED-3, DFN-14 |
| 文件頁數： | 4/16頁 |
| 文件大?。?/td> | 313K |
| 代理商： | LTC3533EDE#TR |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
LTC3533
12
3533f
APPLICATIONS INFORMATION
requirements of the converter. As a rule of thumb, the ratio
of the operating frequency to the unity-gain bandwidth of
the converter is the amount the output capacitance will
have to increase from the above calculations in order to
maintain the desired transient response.
The other component of ripple is due to the ESR (equiva-
lent series resistance) of the output capacitor. Low ESR
capacitors should be used to minimize output voltage
ripple. For surface mount applications, Taiyo Yuden or
TDK ceramic capacitors, AVX TPS series tantalum capaci-
tors or Sanyo POSCAP are recommended. See Table 2 for
contact information.
Input Capacitor Selection
Since PVIN is the supply voltage for the IC it is recom-
mended to place at least a 4.7F, low ESR ceramic bypass
capacitor close to PVIN and GND. It is also important to
minimize any stray resistance from the converter to the
battery or other power source.
Optional Schottky Diodes
Schottky diodes across the synchronous switches B and
D are not required, but do provide a lower drop during the
break-before-make time (typically 15ns), thus improving
efciency. Use a surface mount Schottky diode such as an
MBRM120T3 or equivalent. Do not use ordinary rectier
diodes since their slow recovery times will compromise
efciency.
Output Voltage < 1.8V
The LTC3533 can operate as a buck converter with output
voltages as low as 400mV. The part is specied at 1.8V
minimum to allow operation without the requirement of a
Schottky diode; Since synchronous switch D is powered
from PVOUT, and the RDS(ON) will increase at low output
voltages, a Schottky diode is required from SW2 to VOUT
to provide the conduction path to the output. Note that
Burst Mode operation is inhibited at output voltages below
1V typical.
Output Voltage > 4.3V
A Schottky diode from SW2 to VOUT is required for output
voltages over 4.3V. The diode must be located as close to
the pins as possible in order to reduce the peak voltage on
SW2 due to parasitic lead and trace inductances.
Input Voltage > 4.5V
For applications with input voltages above 4.5V which
could exhibit an overload or short-circuit condition, a
2
Ω/1nF series snubber is required between SW1 and
GND. A Schottky diode from SW1 to PVIN should also be
added as close to the pins as possible. For the higher input
voltages, VIN bypassing becomes more critical. Therefore,
a ceramic bypass capacitor as close to the PVIN and GND
pins as possible is also required.
Operating Frequency Selection
Higher operating frequencies allow the use of a smaller
inductor and smaller input and output lter capacitors,
thus reducing board area and component height. How-
ever, higher operating frequencies also increase the IC’s
total quiescent current due to the gate charge of the four
switches, as given by:
Buck:
IQ = (600e – 12 VIN f ) mA
Boost:
IQ = [800e – 12 (VIN + VOUT) f ] mA
Buck/Boost: IQ = [(1400e – 12 VIN + 400e – 12
VOUT) f ] mA
where f = switching frequency in Hz. Therefore frequency
selection is a compromise between the optimal efciency
and the smallest solution size.
Table 2. Capacitor Vendor Information
SUPPLIER
PHONE
FAX
WEB SITE
AVX
(803) 448-9411
(803) 448-1943
www.avxcorp.com
Sanyo
(619) 661-6322
(619) 661-1055
www.sanyovideo.com
Taiyo Yuden
(408) 573-4150
(408) 573-4159
www.t-yuden.com
TDK
(847) 803-6100
(847) 803-6296
www.component.tdk.com
相關PDF資料 |
PDF描述 |
|---|---|
| LTC3533EDE | 7 A SWITCHING REGULATOR, 2000 kHz SWITCHING FREQ-MAX, PDSO14 |
| LTC3535EDD#PBF | SWITCHING REGULATOR, PDSO12 |
| LTC3538EDCB#PBF | 0.8 A SWITCHING REGULATOR, 1200 kHz SWITCHING FREQ-MAX, PDSO8 |
| LTC3538EDCB | 0.8 A SWITCHING REGULATOR, 1200 kHz SWITCHING FREQ-MAX, PDSO8 |
| LTC3538EDCB#TR | 0.8 A SWITCHING REGULATOR, 1200 kHz SWITCHING FREQ-MAX, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC3534 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:40V, 2A Synchronous Buck-Boost DC/DC |
| LTC3534EDHC#PBF | 功能描述:IC REG BUCK BOOST SYNC ADJ 16DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V，1.5V，1.8V，2.5V 輸入電壓:2.7 V ~ 20 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:50mA 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬）裸露焊盤 包裝:帶卷 (TR) 供應商設備封裝:10-MSOP 裸露焊盤 |
| LTC3534EDHC#TRPBF | 功能描述:IC REG BUCK BOOST SYNC ADJ 16DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V，1.5V，1.8V，2.5V 輸入電壓:2.7 V ~ 20 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:50mA 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬）裸露焊盤 包裝:帶卷 (TR) 供應商設備封裝:10-MSOP 裸露焊盤 |
| LTC3534EGN#PBF | 功能描述:IC REG BUCK BST SYNC 0.5A 16SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:250 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V 輸入電壓:2.05 V ~ 6 V PWM 型:電壓模式 頻率 - 開關:2MHz 電流 - 輸出:500mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-UFDFN 包裝:帶卷 (TR) 供應商設備封裝:6-SON（1.45x1） 產品目錄頁面:1032 (CN2011-ZH PDF) 其它名稱:296-25628-2 |
| LTC3534EGN#TRPBF | 功能描述:IC REG BUCK BST SYNC 0.5A 16SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V，1.5V，1.8V，2.5V 輸入電壓:2.7 V ~ 20 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:50mA 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬）裸露焊盤 包裝:帶卷 (TR) 供應商設備封裝:10-MSOP 裸露焊盤 |
發布緊急采購，3分鐘左右您將得到回復。