- 您現在的位置：買賣IC網 > PDF目錄385506 > LTC2206IUK (LINEAR TECHNOLOGY CORP) 16-Bit, 105Msps/80Msps ADCs PDF資料下載
參數資料
| 型號： | LTC2206IUK |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | ADC |
| 英文描述： | 16-Bit, 105Msps/80Msps ADCs |
| 中文描述： | 1-CH 16-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQCC48 |
| 封裝： | 7 X 7 MM, PLASTIC, MO-220WKKD-2, QFN-48 |
| 文件頁數： | 14/32頁 |
| 文件大?。?/td> | 1489K |
| 代理商： | LTC2206IUK |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
LTC2207/LTC2206
14
22076fa
SENSE (Pin 1):
Reference Mode Select and External
Reference Input. Tie SENSE to V
DD
to select the internal
2.5V bandgap reference. An external reference of 2.5V or
1.25V may be used; both reference values will set a full
scale ADC range of 2.25V (PGA = 0).
V
CM
(Pin 2):
1.25V Output. Optimum voltage for input com-
mon mode. Must be bypassed to ground with a minimum
of 2.2μF. Ceramic chip capacitors are recommended.
V
DD
(Pins 3, 4, 12, 13, 14):
3.3V Analog Supply Pin.
Bypass to GND with 0.1μF ceramic chip capacitors.
GND (Pins 5, 8, 11, 15, 48, 49):
ADC Power Ground.
A
IN+
(Pin 6):
Positive Differential Analog Input.
A
IN–
(Pin 7):
Negative Differential Analog Input.
ENC
+
(Pin 9):
Positive Differential Encode Input. The
sampled analog input is held on the rising edge of ENC
+
.
Internally biased to 1.6V through a 6.2k
Ω
resistor. Output
data can be latched on the rising edge of ENC
+
.
ENC
–
(Pin 10):
Negative Differential Encode Input. The
sampled analog input is held on the falling edge of ENC
–
.
Internally biased to 1.6V through a 6.2k
Ω
resistor. By-
pass to ground with a 0.1μF capacitor for a single-ended
Encode signal.
SHDN (Pin 16):
Power Shutdown Pin. SHDN = low results
in normal operation. SHDN = high results in powered
down analog circuitry and the digital outputs are placed
in a high impedance state.
DITH (Pin 17):
Internal Dither Enable Pin. DITH = low
disables internal dither. DITH = high enables internal
dither. Refer to Internal Dither section of this data sheet
for details on dither operation.
D0-D15 (Pins 18-22, 26-28, 32-35 and 39-42):
Digital
Outputs. D15 is the MSB.
OGND (Pins 23, 31 and 38):
Output Driver Ground.
OV
DD
(Pins 24, 25, 36, 37):
Positive Supply for the Output
Drivers. Bypass to ground with 0.1μF capacitor.
CLKOUT
–
(Pin 29):
Data Valid Output. CLKOUT
–
will toggle
at the sample rate. Latch the data on the falling edge of
CLKOUT
–
.
CLKOUT
+
(Pin 30):
Inverted Data Valid Output. CLKOUT
+
will toggle at the sample rate. Latch the data on the rising
edge of CLKOUT
+
.
OF (Pin 43):
Over/Under Flow Digital Output. OF is high
when an over or under flow has occurred.
O
E (Pin 44):
Output Enable Pin. Low enables the digital
output drivers. High puts digital outputs in Hi-Z state.
MODE (Pin 45):
Output Format and Clock Duty Cycle
Stabilizer Selection Pin. Connecting MODE to 0V selects
offset binary output format and disables the clock duty
cycle stabilizer. Connecting MODE to 1/3V
DD
selects offset
binary output format and enables the clock duty cycle sta-
bilizer. Connecting MODE to 2/3V
DD
selects 2’s complement
output format and enables the clock duty cycle stabilizer.
Connecting MODE to V
DD
selects 2’s complement output
format and disables the clock duty cycle stabilizer.
RAND (Pin 46):
Digital Output Randomization Selection
Pin. RAND low results in normal operation. RAND high
selects D1-D15 to be EXCLUSIVE-ORed with D0 (the
LSB). The output can be decoded by again applying an
XOR operation between the LSB and all other bits. This
mode of operation reduces the effects of digital output
interferance.
PGA (Pin 47):
Programmable Gain Amplifier Control Pin. Low
selects a front-end gain of 1, input range of 2.25V
P-P
. High
selects a front-end gain of 1.5, input range of 1.5V
P-P
.
GND (Exposed Pad, Pin 49):
ADC Power Ground. The ex-
posed pad on the bottom of the package must be soldered
to ground.
PIN FUNCTIONS
相關PDF資料 |
PDF描述 |
|---|---|
| LTC2206UK | 16-Bit, 105Msps/80Msps ADCs |
| LTC2207 | 16-Bit, 105Msps/80Msps ADCs |
| LTC2207CUK | 16-Bit, 105Msps/80Msps ADCs |
| LTC2207IUK | 16-Bit, 105Msps/80Msps ADCs |
| LTC2207UK | 16-Bit, 105Msps/80Msps ADCs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2206IUK#PBF | 制造商:Linear Technology 功能描述:ADC Single Pipelined 80Msps 16-bit Parallel 48-Pin QFN EP 制造商:Linear Technology 功能描述:Single ADC Pipelined 80Msps 16-bit Parallel 48-Pin QFN EP 制造商:Linear Technology 功能描述:IC ADC 16-BIT 80MSPS 48-QFN 制造商:Linear Technology 功能描述:MS-ADC/High Speed, 16-bit, 80Msps ADC 制造商:Linear Technology 功能描述:IC, ADC, 16BIT, 80MSPS, QFN-48, Resolution (Bits):16bit, Sampling Rate:80MSPS, Supply Voltage Type:Single, Supply Voltage Min:3.135V, Supply Voltage Max:3.465V, Supply Current:220mA, Digital IC Case Style:QFN, No. of Pins:48 , RoHS Compliant: Yes |
| LTC2206IUK#TRPBF | 制造商:Linear Technology 功能描述:ADC Single Pipelined 80Msps 16-bit Parallel 48-Pin QFN EP T/R 制造商:Linear Technology 功能描述:IC ADC 16-BIT 80MSPS 48-QFN |
| LTC2206IUK-14 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:14-Bit, 105Msps/80Msps ADCs |
| LTC2206IUK-14#PBF | 功能描述:IC ADC 14BIT 80MSPS 48-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| LTC2206IUK-14#TRPBF | 功能描述:IC ADC 14-BIT 80MSPS 48-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
發(fā)布緊急采購，3分鐘左右您將得到回復。