- 您現在的位置：買賣IC網 > PDF目錄10128 > LTC1608ACG (Linear Technology)IC A/D CONV 16BIT SAMPLNG 36SSOP PDF資料下載
參數資料
| 型號： | LTC1608ACG |
| 廠商： | Linear Technology |
| 文件頁數： | 6/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC A/D CONV 16BIT SAMPLNG 36SSOP |
| 標準包裝： | 37 |
| 位數： | 16 |
| 采樣率（每秒）： | 500k |
| 數據接口： | 并聯 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 420mW |
| 電壓電源： | 模擬和數字，雙 ± |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 36-SSOP（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 36-SSOP |
| 包裝： | 管件 |
| 輸入數目和類型： | 2 個單端，雙極；1 個差分，雙極 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁
14
LTC1608
APPLICATIO S I FOR ATIO
WU
UU
LTC1608
AIN
+
AIN
–
VREF
0V TO
5V
±2.5V
REFCOMP
AGND
1608 F14b
1
2
3
4
5
22
F
ANALOG INPUT
–
+
Figure 14b. Selectable 0V to 5V or
±2.5V Input Range
Differential inputs allow greater flexibility for accepting
different input ranges. Figure 14b shows a circuit that
converts a 0V to 5V analog input signal with only an
additional buffer that is not in the signal path.
Full-Scale and Offset Adjustment
Figure 15a shows the ideal input/output characteristics
for the LTC1608. The code transitions occur midway
between successive integer LSB values (i.e., – FS +
0.5LSB, – FS + 1.5LSB, – FS + 2.5LSB,... FS – 1.5LSB,
FS – 0.5LSB). The output is two’s complement binary with
1LSB = FS – (– FS)/65536 = 5V/65536 = 76.3
V.
In applications where absolute accuracy is important,
offset and full-scale errors can be adjusted to zero. Offset
error must be adjusted before full-scale error. Figure 15b
shows the extra components required for full-scale error
adjustment. Zero offset is achieved by adjusting the offset
applied to the AIN– input. For zero offset error, apply
–38
V (i.e., –0.5LSB) at AIN+ and adjust the offset at the
AIN– input by varying the output voltage of pin VOUTA from
the LTC1662 until the output code flickers between 0000
0000 0000 0000 and 1111 1111 1111 1111. For full-scale
adjustment, an input voltage of 2.499886V (FS/2 – 1.5LSBs)
is applied to AIN+ and the output voltage of pin VOUTB is
adjusted until the output code flickers between 0111 1111
1111 1110 and 0111 1111 1111 1111.
BOARD LAYOUT AND GROUNDING
Wire wrap boards are not recommended for high resolu-
tion or high speed A/D converters. To obtain the best per-
formance from the LTC1608, a printed circuit board with
ANALOG
INPUT
1608 F15b
1
2
3
80.6k
1%
OFFSET ADJ RANGE:
±0.125%
FULL-SCALE ADJ RANGE:
±0.25%
R1
40.2k
4
5
0.1
F
5V
22
F
–5V
R3
1.5M
R2
100
+
2.2
F
+
AIN
+
AIN
–
VREF
REFCOMP
AGND
LTC1608
LTC1662
CS/LD
SCK
SDI
REF
VOUTA
GND
VCC
VOUTB
Figure 15b. Offset and Full-Scale Adjust Circuit
1608 F15a
011...111
011...110
000...001
000...000
111...111
111...110
100...001
100...000
FS – 1LSB
– (FS – 1LSB)
INPUT VOLTAGE (AIN
+ – A
IN
–)
OUTPUT
CODE
Figure 15a. LTC1608 Transfer Characteristics
ground plane is required. Layout should ensure that digital
and analog signal lines are separated as much as possible.
Particular care should be taken not to run any digital track
alongside an analog signal track or underneath the ADC.The
analog input should be screened by AGND.
An analog ground plane separate from the logic system
ground should be established under and around the ADC.
Pin 5 to Pin 8 (AGNDs), Pin 10 (ADC’s DGND) and all other
analog grounds should be connected to this single analog
ground point. The REFCOMP bypass capacitor and the
DVDD bypass capacitor should also be connected to this
analog ground plane. No other digital grounds should be
connected to this analog ground plane. Low impedance
analog and digital power supply common returns are
essential to low noise operation of the ADC and the foil
width for these tracks should be as wide as possible. In
相關PDF資料 |
PDF描述 |
|---|---|
| PXA921/07/P | CONN RCPT 7POS W/PINS LG CABLE |
| IDT72V201L20J8 | IC FIFO SYNC 256X9 20NS 32-PLCC |
| IDT72V03L25J8 | IC ASYNCH 2048X9 25NS 32-PLCC |
| AD7701BRZ-REEL | IC ADC 16BIT LC2MOS 20SOIC |
| LT1791ACN#PBF | IC TXRX 60V RS485/RS422 14DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1608ACG#PBF | 功能描述:IC A/D CONV 16BIT SAMPLNG 36SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| LTC1608ACG#PBF | 制造商:Linear Technology 功能描述:ADC, 16BIT, 500KSPS, SSOP-36 |
| LTC1608ACG#TR | 功能描述:IC ADC 16BIT 5V SAMPLING 36SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| LTC1608ACG#TRPBF | 功能描述:IC A/D CONV 16BIT SAMPLNG 36SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| LTC1608AIG | 功能描述:IC CONV A/D 16BIT 500KSPS 36SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
發布緊急采購，3分鐘左右您將得到回復。