- 您現在的位置：買賣IC網 > PDF目錄385502 > LTC1261 (Linear Technology Corporation) Switched Capacitor Regulated Voltage Inverter(開關電容穩壓電壓反相器) PDF資料下載
參數資料
| 型號： | LTC1261 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | Switched Capacitor Regulated Voltage Inverter(開關電容穩壓電壓反相器) |
| 中文描述： | 開關電容穩壓逆變器（開關電容穩壓電壓反相器） |
| 文件頁數： | 5/16頁 |
| 文件大?。?/td> | 265K |
| 代理商： | LTC1261 |
5
LTC1261
PI
FU
CTIO
N
S
U
U
Pin numbers are shown as (LTC1261CS/LTC1261CS8).
NC (Pin 1/NA):
No Internal Connection.
C1
+
(Pin 2/Pin 2):
C1 Positive Input. Connect a 0.1
μ
F
capacitor between C1
+
and C1
–
. With the LTC1261CS in
doubler mode, connect a 0.1
μ
F capacitor from C1
+
to
C2
–
.
C1
–
(Pin 3/Pin 3):
C1 Negative Input. Connect a 0.1
μ
F
capacitor from C1
+
to C1
–
. With the LTC1261CS in
doubler mode only, C1
–
should float.
C2
+
(Pin 4/NA)
: C2 Positive Input. In tripler mode con-
nect a 0.1
μ
F capacitor from C2
+
to C2
–
. This pin is used
with the LTC1261CS in tripler mode only; in doubler
mode this pin should float.
C2
–
(Pin 5/NA):
C2 Negative Input. In tripler mode
connect a 0.1
μ
F capacitor from C2
+
to C2
–
. In doubler
mode connect a 0.1
μ
F capacitor from C1
+
to C2
–
.
GND (Pin 6/Pin 4):
Ground. Connect to a low impedance
ground. A ground plane will help to minimize regulation
errors.
R0 (Pin 7/NA):
Internal Resistor String, 1st Tap. See
Table 2 in the Applications Information section for infor-
mation on internal resistor string pin connections vs
output voltage.
R1 (Pin 8/NA):
Internal Resistor String, 2nd Tap.
R
ADJ
(Pin 9/NA):
Internal Resistor String Output. Con-
nect this pin to ADJ to use the internal resistor divider.
See Table 2 in the Applications Information section for
information on internal resistor string pin connections vs
output voltage.
ADJ (COMP for fixed versions) (Pin 10/Pin 5):
Output
Adjust/Compensation Pin. For adjustable parts this pin is
used to set the output voltage. The output voltage should
be divided down with a resistor divider and fed back to
this pin to set the regulated output voltage. The resistor
divider can be external or the internal divider string can
be used if it can provide the required output voltage.
Typically the resistor string should draw
≥
10
μ
A from the
output to minimize errors due to the bias current at the
adjust pin. Fixed output parts have the internal resistor
string connected to this pin inside the package. The pin
can be used to trim the output voltage if desired. It can
also be used as an optional feedback compensation pin
to reduce output ripple on both adjustable and fixed
output voltage parts. See Applications Information sec-
tion for more information on compensation and output
ripple.
OUT (Pin 11/Pin 6):
Negative Voltage Output. This pin
must be bypassed to ground with a 1
μ
F or larger capaci-
tor; it must be at least 3.3
μ
F to provide specified output
ripple. The size of the output capacitor has a strong effect
on output ripple. See the Applications Information sec-
tion for more details.
REG (Pin 12/Pin 7):
This is an open drain output that pulls
low when the output voltage is within 5% of the set value.
It will sink 8mA to ground with a 5V supply. The external
circuitry must provide a pull-up or REG will not swing
high. The voltage at REG may exceed V
CC
and can be
pulled up to 12V above ground without damage.
SHDN (Pin 13/Pin 8):
Shutdown. When this pin is at
ground the LTC1261 operates normally. An internal 5
μ
A
pull-down keeps SHDN low if it is left floating. When
SHDN is pulled high, the LTC1261 enters shutdown
mode. In shutdown the charge pump stops, the output
collapses to 0V and the quiescent current drops to 5
μ
A
typically.
V
CC
(Pin 14/Pin 1):
Power Supply. This requires an input
voltage between 3V and 6.5V. Certain combinations of
output voltage and operating mode may place additional
restrictions on the input voltage. V
CC
must be bypassed
to ground with at least a 0.1
μ
F capacitor placed in close
proximity to the chip. See the Applications Information
section for details.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1262 | Regulated 12V, 30mA output DC/DC converter.(12V穩壓, 30mA輸出DC/DC變換器) |
| LTC1263 | Regulated 12V, 60mA output DC/DC converter.(12V穩壓, 60mA輸出DC/DC變換器) |
| LTC1264CSW | High Speed, Quad Universal Filter Building Block |
| LTC1265-3.3 | 1.2A, High Efficiency Step-Down Current Mode DC/DC Converter(3.3V,12A,高效率,電流模式步降DC/DC變換器) |
| LTC1265-5 | 1.2A, High Efficiency Step-Down Current Mode DC/DC Converter(5V,12A,高效率,電流模式步降DC/DC變換器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1261CS | 功能描述:IC REG SWITCHED CAP INV 14SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V，1.5V，1.8V，2.5V 輸入電壓:2.7 V ~ 20 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:50mA 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬）裸露焊盤 包裝:帶卷 (TR) 供應商設備封裝:10-MSOP 裸露焊盤 |
| LTC1261CS#PBF | 功能描述:IC REG SWITCHED CAP INV 14SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 產品培訓模塊:MIC23xxx HyperLight Load™ Regulators 標準包裝:5,000 系列:HyperLight Load® 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.8V 輸入電壓:2.7 V ~ 5.5 V PWM 型:混合物 頻率 - 開關:4MHz 電流 - 輸出:2A 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-VFDFN 裸露焊盤，8-MLF? 包裝:帶卷 (TR) 供應商設備封裝:8-MLF?（2x2） 產品目錄頁面:1094 (CN2011-ZH PDF) 其它名稱:576-3303-2 |
| LTC1261CS#TR | 功能描述:IC REG SWITCHED CAP INV 14SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:升壓（升壓） 輸出類型:可調式 輸出數:1 輸出電壓:1.24 V ~ 30 V 輸入電壓:1.5 V ~ 12 V PWM 型:電流模式，混合 頻率 - 開關:600kHz 電流 - 輸出:500mA 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) 供應商設備封裝:8-SOIC |
| LTC1261CS#TRPBF | 功能描述:IC REG SWITCHED CAP INV 14SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:升壓（升壓） 輸出類型:可調式 輸出數:1 輸出電壓:1.24 V ~ 30 V 輸入電壓:1.5 V ~ 12 V PWM 型:電流模式，混合 頻率 - 開關:600kHz 電流 - 輸出:500mA 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) 供應商設備封裝:8-SOIC |
| LTC1261CS8 | 功能描述:IC REG SWITCHD CAP INV ADJ 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:升壓（升壓） 輸出類型:可調式 輸出數:1 輸出電壓:1.24 V ~ 30 V 輸入電壓:1.5 V ~ 12 V PWM 型:電流模式，混合 頻率 - 開關:600kHz 電流 - 輸出:500mA 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) 供應商設備封裝:8-SOIC |
發布緊急采購，3分鐘左右您將得到回復。