- 您現在的位置：買賣IC網 > PDF目錄385502 > LTC1147IS8-5 (LINEAR TECHNOLOGY CORP) RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS PDF資料下載
參數資料
| 型號： | LTC1147IS8-5 |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| 中文描述： | SWITCHING CONTROLLER, 400 kHz SWITCHING FREQ-MAX, PDSO8 |
| 封裝： | 0.150 INCH, PLASTIC, SO-8 |
| 文件頁數： | 8/16頁 |
| 文件大小： | 225K |
| 代理商： | LTC1147IS8-5 |
8
LTC1147-3.3
LTC1147-5/LTC1147L
sn1147 1147fds
series will delay entering Burst Mode operation and effi-
ciency will be degraded at low currents.
Inductor Core Selection
Once the minimum value for L is known, the type of
inductor must be selected. Highest efficiency will be
obtained using ferrite, Kool M
μ
(from Magnetics, Inc.) or
molypermalloy (MPP) cores. Lower cost powdered iron
cores provide suitable performance but cut efficiency by
3% to 5%. Actual core loss is independent of core size for
a fixed inductor value, but it is very dependent on induc-
tance selected. As inductance increases, core losses go
down. Unfortunately, increased inductance requires more
turns of wire and therefore copper losses will increase.
Ferrite designs have very low core loss, so design goals
can concentrate on copper loss and preventing satura-
tion. Ferrite core material saturates “hard,” which means
that inductance collapses abruptly when the peak design
current is exceeded. This results in an abrupt increase in
inductor ripple current and consequent output voltage
ripple which can cause Burst Mode operation to be
falsely triggered in the LTC1147. Do not allow the core
to saturate!
Kool M
μ
is a very good, low loss core material for toroids
with a “soft” saturation characteristic. Molypermalloy is
slightly more efficient at high (>200kHz) switching fre-
quencies but quite a bit more expensive. Toroids are very
space efficient, especially when you can use several
layers of wire. Because they generally lack a bobbin,
mounting is more difficult. However, new designs for
surface mount are available from Coiltronics, Sumida and
Beckman Industrial Corp. which do not increase the
height significantly.
Power MOSFET Selection
An external P-channel power MOSFET must be selected
for use with the LTC1147 series. The main selection
criteria for the power MOSFET are the threshold voltage
V
GS(TH)
and “on” resistance R
DS(ON)
.
The minimum input voltage determines whether a stan-
dard threshold or logic-level threshold MOSFET must be
FREQUENCY (kHz)
0
0
C
200
400
600
100
200
LTC1147 F03
800
1000
300
V
SENSE–
= V
OUT
= 5V
V
IN
= 10V
V
IN
= 7V
V
IN
= 12V
Figure 3. Timing Capacitor Value
is given by:
f
≈
1
t
OFF
)
)
1 –V
OUT
V
IN
where:
t
OFF
= (1.3)(10
4
)(C
T
)
)
)
V
REG
V
OUT
V
REG
is the desired output voltage (i.e., 5V, 3.3V). V
OUT
is
the measured output voltage. Thus V
REG
/V
OUT
= 1 in
regulation.
Note that as V
IN
decreases, the frequency decreases.
When the input to output voltage differential drops
below 1.5V, the LTC1147 reduces t
OFF
by increasing the
discharge current in C
T
. This prevents audible opera-
tion prior to dropout.
Once the frequency has been set by C
T
, the inductor L
must be chosen to provide no more than 25mV/R
SENSE
of peak-to-peak inductor ripple current. This results in
a minimum required inductor value of:
L
MIN
= (5.1)(10
5
)(R
SENSE
)(C
T
)(V
REG
)
As the inductor value is increased from the minimum
value, the ESR requirements for the output capacitor
are eased at the expense of efficiency. If too small an
inductor is used, the inductor current will become
discontinuous before the LTC1147 series enters Burst
Mode operation.
A consequence of this is that the LTC1147
Kool M
μ
is a registered trademark of Magnetics, Inc.
APPLICATIU
W
U
U
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1148HVIS-5 | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| LTC1151CSW | Dual 【15V Zero-Drift Operational Amplifier |
| LTC1151 | Dual ±15V Zero-Drift Operational Amplifier(±15V，雙路，零漂移運算放大器) |
| LTC1153 | Auto-Reset Electronic Circuit Breaker |
| LTC1153C | Auto-Reset Electronic Circuit Breaker |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1147IS8-5#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 8-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR) |
| LTC1147IS8-5#TR | 功能描述:IC REG CTRLR BUCK PWM CM 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR) |
| LTC1147IS8-5#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 8-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR) |
| LTC1147L | 制造商:LINER 制造商全稱:Linear Technology 功能描述:High Efficiency Step-Down Switching Regulator Controllers |
| LTC1147LCS8 | 功能描述:IC REG CTRLR BUCK PWM CM 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,500 系列:PowerWise® PWM 型:控制器 輸出數:1 頻率 - 最大:1MHz 占空比:95% 電源電壓:2.8 V ~ 5.5 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:6-WDFN 裸露焊盤 包裝:帶卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名稱:LM1771SSDX |
發布緊急采購，3分鐘左右您將得到回復。