參數資料
型號: LTC1147IS8-5
廠商: LINEAR TECHNOLOGY CORP
元件分類: 穩壓器
英文描述: RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS
中文描述: SWITCHING CONTROLLER, 400 kHz SWITCHING FREQ-MAX, PDSO8
封裝: 0.150 INCH, PLASTIC, SO-8
文件頁數: 10/16頁
文件大小: 225K
代理商: LTC1147IS8-5
10
LTC1147-3.3
LTC1147-5/LTC1147L
sn1147 1147fds
Optimum efficiency is obtained by making the ESR equal
to R
SENSE
. As the ESR is increased up to 2R
SENSE
, the
efficiency degrades by less than 1%. If the ESR is greater
than 2R
SENSE
, the voltage ripple on the output capacitor
will prematurely trigger Burst Mode
operation, resulting in
disruption of continuous mode and an efficiency hit which
can be several percent.
Manufacturers such as Nichicon and United Chemicon
should be considered for high performance capacitors.
The OS-CON semiconductor dielectric capacitor available
from Sanyo has the lowest ESR/size ratio of any aluminum
electrolytic at a somewhat higher price. Once the ESR
requirement for C
OUT
has been met, the RMS current
rating generally far exceeds the I
RIPPLE(P-P)
requirement.
In surface mount applications multiple capacitors may
have to be paralleled to meet the capacitance, ESR or RMS
current handling requirements of the application. Alumi-
num electrolytic and dry tantalum capacitors are both
available in surface mount configurations. In the case of
tantalum, it is critical that the capacitors are surge tested
for use in switching power supplies. An excellent choice
is the AVX TPS series of surface mount tantalums, avail-
able in case heights ranging from 2mm to 4mm. For
example, if 200
μ
F/10V is called for in an application
requiring 3mm height, two AVX 100
μ
F/10V (P/N TPSD
107K010) could be used. Consult the manufacturer for
other specific recommendations.
At low supply voltages, a minimum capacitance at C
OUT
is
needed to prevent an abnormal low frequency operating
mode (see Figure 4). When C
OUT
is made too small, the
output ripple at low frequencies will be large enough to trip
the voltage comparator. This causes Burst Mode
opera-
tion to be activated when the LTC1147 series would
normally be in continuous operation. The effect is most
pronounced with low values of R
SENSE
and can be im-
proved by operating at higher frequencies with lower
values of L. The output remains in regulation at all times.
Checking Transient Response
The regulator loop response can be checked by looking
at the load transient response. Switching regulators
take several cycles to respond to a step in DC (resistive)
load current. When a load step occurs, V
OUT
shifts by an
amount equal to
I
LOAD
(ESR), where ESR is the effec-
tive series resistance of C
OUT
.
I
LOAD
also begins to
charge or discharge C
OUT
until the regulator loop adapts
to the current change and returns V
OUT
to its steady
state value. During this recovery time V
OUT
can be
monitored for overshoot or ringing which would indi-
cate a stability problem. The external components shown
in the Figure 1 circuit will prove adequate compensation
for most applications.
A second, more severe transient is caused by switching
in loads with large (>1
μ
F) supply bypass capacitors. The
discharged bypass capacitors are effectively put in par-
allel with C
OUT
, causing a rapid drop in V
OUT
. No regulator
can deliver enough current to prevent this problem if the
load switch resistance is low and it is driven quickly. The
only solution is to limit the rise time of the switch drive so
that the load rise time is limited to approximately
(25)C
LOAD
. Thus a 10
μ
F capacitor would require a 250
μ
s
rise time, limiting the charging current to about 200mA.
Efficiency Considerations
The percent efficiency of a switching regulator is equal to
the output power divided by the input power times 100%.
It is often useful to analyze individual losses to determine
what is limiting the efficiency and which change would
produce the most improvement. Percent efficiency can be
expressed as:
%Efficiency = 100% – (L1 + L2 + L3 + ...)
Figure 4. Minimum Value of C
OUT
(V
IN
– V
OUT
) VOLTAGE (V)
0
C
O
μ
F600
1000
4
LTC1147 F04
400
200
0
1
2
3
5
800
L = 50
μ
H
R
SENSE
= 0.02
L = 25
μ
H
R
SENSE
= 0.02
L = 50
μ
H
R
SENSE
= 0.05
APPLICATIU
W
U
U
相關PDF資料
PDF描述
LTC1148HVIS-5 RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS
LTC1151CSW Dual 【15V Zero-Drift Operational Amplifier
LTC1151 Dual ±15V Zero-Drift Operational Amplifier(±15V,雙路,零漂移運算放大器)
LTC1153 Auto-Reset Electronic Circuit Breaker
LTC1153C Auto-Reset Electronic Circuit Breaker
相關代理商/技術參數
參數描述
LTC1147IS8-5#PBF 功能描述:IC REG CTRLR BUCK PWM CM 8-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR)
LTC1147IS8-5#TR 功能描述:IC REG CTRLR BUCK PWM CM 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR)
LTC1147IS8-5#TRPBF 功能描述:IC REG CTRLR BUCK PWM CM 8-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR)
LTC1147L 制造商:LINER 制造商全稱:Linear Technology 功能描述:High Efficiency Step-Down Switching Regulator Controllers
LTC1147LCS8 功能描述:IC REG CTRLR BUCK PWM CM 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,500 系列:PowerWise® PWM 型:控制器 輸出數:1 頻率 - 最大:1MHz 占空比:95% 電源電壓:2.8 V ~ 5.5 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:6-WDFN 裸露焊盤 包裝:帶卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名稱:LM1771SSDX