- 您現在的位置：買賣IC網 > PDF目錄30768 > LT8410EDC-1#PBF (LINEAR TECHNOLOGY CORP) 0.01 A SWITCHING REGULATOR, PDSO8 PDF資料下載
參數資料
| 型號： | LT8410EDC-1#PBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 0.01 A SWITCHING REGULATOR, PDSO8 |
| 封裝： | 2 X 2 MM, LEAD FREE, PLASTIC, DFN-8 |
| 文件頁數： | 2/16頁 |
| 文件大?。?/td> | 309K |
| 代理商： | LT8410EDC-1#PBF |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
LT8410/LT8410-1
10
84101fb
APPLICATIONS INFORMATION
Step 4. Calculate the nominal output current:
IOUT(NOM) =
IIN(AVG) VIN 0.7
VOUT
mA
Step 5. Derate output current:
IOUT = IOUT(NOM) 0.8
For low output voltages the output current capability will
be increased. When using output disconnect (load current
taken from VOUT), these higher currents will cause the
drop in the PMOS switch to be higher resulting in lower
output current capability than predicted by the preceding
equations.
Inrush Current
When VCC is stepped from ground to the operating voltage
while the output capacitor is discharged, a high level of
inrushcurrentmayflowthroughtheinductorandSchottky
diode into the output capacitor. Conditions that increase
inrush current include a larger more abrupt voltage step
at VCC, a larger output capacitor tied to the CAP pin and
an inductor with a low saturation current. While the chip is
designed to handle such events, the inrush current should
not be allowed to exceed 0.3A. For circuits that use output
capacitor values within the recommended range and have
input voltages of less than 6V, inrush current remains low,
posing no hazard to the device. In cases where there are
large steps at VCC (more than 6V) and/or a large capacitor
is used at the CAP pin, inrush current should be measured
to ensure safe operation.
Soft-Start
The LT8410 series contains a soft-start circuit to limit
peak switch currents during start-up. High start-up cur-
rent is inherent in switching regulators, in general, since
the feedback loop is saturated due to VOUT being far from
its final value. The regulator tries to charge the output
capacitor as quickly as possible, which results in large
peak current.
When the FBP pin voltage is generated by a resistor divider
from the VREF pin, the start-up current can be limited by
connecting an external capacitor (typically 47nF to 220nF)
to the VREF pin. When the part is brought out of shutdown,
this capacitor is first discharged for about 70μs (providing
protection against pin glitches and slow ramping), then
an internal 10μA current source pulls the VREF pin slowly
to 1.235V. Since the VOUT voltage is set by the FBP pin
voltage, the VOUT voltage will also slowly increase to the
regulated voltage, which results in lower peak inductor
current. The voltage ramp rate on the pin can be set by
the value of the VREF pin capacitor.
Output Disconnect
The LT8410 series has an output disconnect PMOS that
blocks the load from the input during shutdown. The
maximumcurrentthroughthePMOSislimitedbycircuitry
inside the chip, helping the chip survive output shorts.
SHDN Pin Comparator and Hysteresis Current
An internal comparator compares the SHDN pin voltage
with an internal voltage reference (1.3V) which gives a
preciseturn-onvoltagelevel.Theinternalhysteresisofthis
turn-onvoltageis about 60mV. When thechipis turnedon,
and the SHDN pin voltage is close to this turn-on voltage,
0.1μA current flows out of the SHDN pin. This current is
called SHDN pin hysteresis current, and will go away when
the chip is off. By connecting the external resistors as in
Figure 2, a user-programmable enable voltage function
can be realized.
The turn-on voltage for the configuration is:
1.30 1
+
R1
R2
and the turn-off voltage is:
1.24
R3 107
(
) 1+ R1
R2
(R1 107)
where R1, R2 and R3 are resistance value in Ω.
R1
ENABLE VOLTAGE
R2
R3
CONNECT TO
SHDN PIN
84101 F02
Figure 2. Programming Enable Voltage by Using External Resistors
相關PDF資料 |
PDF描述 |
|---|---|
| LT8410EDC-1#TRPBF | 0.01 A SWITCHING REGULATOR, PDSO8 |
| LT8410IDC#PBF | 0.03 A SWITCHING REGULATOR, PDSO8 |
| LTC1044CDR | SWITCHED CAPACITOR CONVERTER, 5 kHz SWITCHING FREQ-MAX, PDSO8 |
| LTC1044CD | SWITCHED CAPACITOR CONVERTER, 5 kHz SWITCHING FREQ-MAX, PDSO8 |
| LTC1044ML/883B | SWITCHED CAPACITOR CONVERTER, 5 kHz SWITCHING FREQ-MAX, MBCY8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT8410EDC-1-TRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Ultralow Power Boost Converter with Output Disconnect |
| LT8410EDC-PBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Ultralow Power Boost Converter with Output Disconnect |
| LT8410EDC-TRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Ultralow Power Boost Converter with Output Disconnect |
| LT8410IDC#PBF | 制造商:Linear Technology 功能描述:Conv DC-DC Single Step Up 2.5V to 16V 8-Pin DFN EP |
| LT8410IDC#TRMPBF | 功能描述:IC REG BOOST ADJ 8DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:升壓（升壓） 輸出類型:可調式 輸出數:1 輸出電壓:1.24 V ~ 30 V 輸入電壓:1.5 V ~ 12 V PWM 型:電流模式，混合 頻率 - 開關:600kHz 電流 - 輸出:500mA 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) 供應商設備封裝:8-SOIC |
發布緊急采購，3分鐘左右您將得到回復。