- 您現在的位置：買賣IC網 > PDF目錄44987 > LT3956IUHE#TRPBF (LINEAR TECHNOLOGY CORP) SWITCHING REGULATOR, PQCC36 PDF資料下載
參數資料
| 型號： | LT3956IUHE#TRPBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | SWITCHING REGULATOR, PQCC36 |
| 封裝： | 5 X 6 MM, LEAD FREE, PLASTIC, QFN-36 |
| 文件頁數： | 5/20頁 |
| 文件大?。?/td> | 1424K |
| 代理商： | LT3956IUHE#TRPBF |
LT3956
3956f
applicaTions inForMaTion
will be enabled after the device temperature drops 10°C.
This function is intended to protect the device during
momentary overload conditions.
The major contributors to internal power dissipation are
the current in the linear regulator to drive the switch, and
the ohmic losses in the switch. The linear regulator power
is proportional to VIN and switching frequency, so at high
VIN the switching frequency should be chosen carefully
to ensure that the IC does not exceed a safe junction
temperature. The internal junction temperature of the IC
can be estimated by:
TJ = TA + [VIN (IQ + fSW 7nC) + ISW2 0.14Ω DSW]
θJA
where TA is the ambient temperature, IQ is the quiescent
current of the part (maximum 1.7mA) and
θJA is the
package thermal impedance (43°C/W for the 5mm
× 6mm
QFN package). For example, an application with TA(MAX) =
85°C, VIN(MAX)=60V,fSW=400kHz,andhavinganaverage
switching current of 2.5A at 70% duty cycle, the maximum
IC junction temperature will be approximately:
TJ = 85°C + [(2.5A)2 0.14Ω 0.7 + 60V
(1.7mA + 400kHz 7nC)] 43°C/W= 123°C
The Exposed Pads on the bottom of the package must be
solderedtoaplane.Theseshouldthenbeconnectedtointer-
nal copper planes with thermal vias placed directly under
the package to spread out the heat dissipated by the IC.
Open LED Detection
The LT3956 provides an open-drain status pin, VMODE,
that pulls low when the FB pin is within ~50mV of its 1.25V
regulated voltage. If the open LED clamp voltage is pro-
grammedcorrectlyusingtheFBpin,thentheFBpinshould
neverexceed1.1VwhenLEDsareconnected,therefore,the
only way for the FB pin to be within 50mV of the regulation
voltage is for an open LED event to have occurred.
Input Capacitor Selection
The input capacitor supplies the transient input current for
the power inductor of the converter and must be placed
and sized according to the transient current requirements.
Theswitchingfrequency,outputcurrentandtolerableinput
voltage ripple are key inputs to estimating the capacitor
value. An X7R type ceramic capacitor is usually the best
choice since it has the least variation with temperature and
DC bias. Typically, boost and SEPIC converters require a
lower value capacitor than a buck mode converter. As-
suming that a 100mV input voltage ripple is acceptable,
the required capacitor value for a boost converter can be
estimated as follows:
C
I
V
T
F
A s
IN F
LED A
OUT
IN
SW s
( )
=
1
Therefore, a 4.7F capacitor is an appropriate selection
for a 400kHz boost regulator with 12V input, 48V output
and 1A load.
WiththesameVINvoltagerippleof100mV,theinputcapaci-
tor for a buck converter can be estimated as follows:
C
I
T
F
A s
IN F
LED A
SW s
( )
.
=
4 7
A 10F input capacitor is an appropriate selection for a
400kHz buck mode converter with a 1A load.
In the buck mode configuration, the input capacitor has
large pulsed currents due to the current returned through
the Schottky diode when the switch is off. In this buck
converter case it is important to place the capacitor as
close as possible to the Schottky diode and to the PGND
return of the switch. It is also important to consider the
ripple current rating of the capacitor. For best reliability,
this capacitor should have low ESR and ESL and have an
adequate ripple current rating. The RMS input current for
a buck mode LED driver is:
IIN(RMS) =
( )
I
D D
LED
–
1
where D is the switch duty cycle.
Table 2. Recommended Ceramic Capacitor Manufacturers
MANUFACTURER
WEB SITE
TDK
www.tdk.com
Kemet
www.kemet.com
Murata
www.murata.com
Taiyo Yuden
www.t-yuden.com
相關PDF資料 |
PDF描述 |
|---|---|
| LT3957EUHE#TRPBF | SWITCHING REGULATOR, PQCC36 |
| LT3957IUHE#PBF | SWITCHING REGULATOR, PQCC36 |
| LT3958IUHE#PBF | SWITCHING REGULATOR, PQCC36 |
| LT3958EUHE#PBF | SWITCHING REGULATOR, PQCC36 |
| LT3958EUHE#TRPBF | SWITCHING REGULATOR, PQCC36 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT3957 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Wide Input Voltage Range |
| LT3957A | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Boost, Flyback, SEPIC and Inverting Converter |
| LT3957AEUHE#PBF | 功能描述:IC REG MULTI CONFIG ADJ 5A 36QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:250 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V 輸入電壓:2.05 V ~ 6 V PWM 型:電壓模式 頻率 - 開關:2MHz 電流 - 輸出:500mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-UFDFN 包裝:帶卷 (TR) 供應商設備封裝:6-SON（1.45x1） 產品目錄頁面:1032 (CN2011-ZH PDF) 其它名稱:296-25628-2 |
| LT3957AEUHE#TRPBF | 功能描述:IC REG MULTI CONFIG ADJ 5A 36QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V，1.5V，1.8V，2.5V 輸入電壓:2.7 V ~ 20 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:50mA 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬）裸露焊盤 包裝:帶卷 (TR) 供應商設備封裝:10-MSOP 裸露焊盤 |
| LT3957AIUHE#PBF | 功能描述:IC REG MULTI CONFIG ADJ 5A 36QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:250 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V 輸入電壓:2.05 V ~ 6 V PWM 型:電壓模式 頻率 - 開關:2MHz 電流 - 輸出:500mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-UFDFN 包裝:帶卷 (TR) 供應商設備封裝:6-SON（1.45x1） 產品目錄頁面:1032 (CN2011-ZH PDF) 其它名稱:296-25628-2 |
發布緊急采購，3分鐘左右您將得到回復。