- 您現在的位置：買賣IC網 > PDF目錄44987 > LT3956IUHE#TRPBF (LINEAR TECHNOLOGY CORP) SWITCHING REGULATOR, PQCC36 PDF資料下載
參數資料
| 型號： | LT3956IUHE#TRPBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | SWITCHING REGULATOR, PQCC36 |
| 封裝： | 5 X 6 MM, LEAD FREE, PLASTIC, QFN-36 |
| 文件頁數： | 18/20頁 |
| 文件大小： | 1424K |
| 代理商： | LT3956IUHE#TRPBF |
LT3956
3956f
pin FuncTions
FB: Voltage Loop Feedback Pin. FB is intended for con-
stant-voltage regulation or for LED protection/open LED
detection. The internal transconductance amplifier with
output VC will regulate FB to 1.25V (nominal) through the
DC/DC converter. If the FB input is regulating the loop, the
VMODE pull-down is asserted. This action may signal an
open LED fault. If FB is driven above the FB threshold (by
an external power supply spike, for example), the VMODE
pull-down will be de-asserted and the PWMOUT pin will
be driven low to protect the LEDs from an overcurrent
event. Do not leave the FB pin open. If not used, connect
to GND.
ISN: Connection point for the negative terminal of the
current feedback resistor. If ISN is greater than 2.9V, the
LED current can be programmed by ILED = 250mV/RLED
when VCTRL > 1.2V or ILED = (VCTRL –100mV)/(4 RLED)
if VCTRL < 1V. Input bias current is typically 20A. Below
3V, ISN is an input to the short-circuit protection feature
that forces GATE to 0V if ISP exceeds ISN by more than
350mV (typ).
ISP:Connectionpointforthepositiveterminalofthecurrent
feedback resistor. Input bias current for this pin depends
on CTRL pin voltage, as shown in the Typical Performance
Characteristics. ISP is an input to the short-circuit protec-
tion feature when ISN is less than 3V.
VC: Transconductance Error Amplifier Output Pin. This pin
is used to stabilize the voltage loop with an RC network.
This pin is high impedance when PWM is low, a feature
that stores the demand current state variable for the next
PWM high transition. Connect a capacitor between this
pin and GND; a resistor in series with the capacitor is
recommended for fast transient response.
CTRL: Current Sense Threshold Adjustment Pin. Regula-
ting threshold V(ISP – ISN) is 0.25 VCTRL plus an offset
for 0V < VCTRL < 1V. For VCTRL > 1.2V the current sense
threshold is constant at the full-scale value of 250mV. For
1V < VCTRL < 1.2V, the dependence of the current sense
threshold upon VCTRL transitions from a linear function
to a constant value, reaching 98% of full-scale value by
VCTRL = 1.1V. Connect CTRL to VREF for the 250mV default
threshold. Do not leave this pin open.
NC:NoInternalConnection.Thesepinsmaybeleftfloating
or connected to an adjacent pin.
EN/UVLO: Shutdown and Undervoltage Detect Pin. An
accurate 1.22V falling threshold with externally program-
mable hysteresis detects when power is OK to enable
switching. Rising hysteresis is generated by the external
resistor divider and an accurate internal 2.1A pull-down
current. Above the 1.24V (nominal) threshold (but below
6V), EN/UVLO input bias current is sub-A. Below the
falling threshold, a 2.1A pull-down current is enabled so
the user can define the hysteresis with the external resis-
tor selection. An undervoltage condition resets soft-start.
Tie to 0.4V, or less, to disable the device and reduce VIN
quiescent current below 1A.
INTVCC: Regulated supply for internal loads, GATE driver
and PWMOUT driver. Supplied from VIN and regulates to
7.15V (typical). INTVCC must be bypassed with a 4.7F
capacitor placed close to the pin. Connect INTVCC directly
to VIN if VIN is always less than or equal to 7V.
GND: Ground. The exposed pad, Pin 37, is ground and
must be soldered directly to the ground plane.
VIN: Input Supply Pin. Must be locally bypassed with
a 0.22F (or larger) capacitor to PGND placed close to
the IC.
SW: The exposed pad, Pin 38, is the drain of the switch-
ing N-channel MOSFET and must be connected to the
external inductor.
PGND: Source terminal of switch and the GND input to
the switch current comparator. Kelvin connect to the GND
plane close to the IC using Pin 12. Pins 13 to 17 should be
connectedexternallytothePGNDterminalsofcomponents
in the switching path. See the Board Layout section.
PWMOUT: Buffered Version of the PWM Signal. This pin is
used to drive the LED load disconnect N-channel MOSFET
or level shift. This pin also serves in a protection function
for the FB overvoltage condition—will toggle if the FB
input is greater than the FB regulation voltage (VFB) plus
60mV (typical). The PWMOUT pin is driven from INTVCC.
Use of a MOSFET with gate cut-off voltage higher than
1V is recommended.
相關PDF資料 |
PDF描述 |
|---|---|
| LT3957EUHE#TRPBF | SWITCHING REGULATOR, PQCC36 |
| LT3957IUHE#PBF | SWITCHING REGULATOR, PQCC36 |
| LT3958IUHE#PBF | SWITCHING REGULATOR, PQCC36 |
| LT3958EUHE#PBF | SWITCHING REGULATOR, PQCC36 |
| LT3958EUHE#TRPBF | SWITCHING REGULATOR, PQCC36 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT3957 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Wide Input Voltage Range |
| LT3957A | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Boost, Flyback, SEPIC and Inverting Converter |
| LT3957AEUHE#PBF | 功能描述:IC REG MULTI CONFIG ADJ 5A 36QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:250 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V 輸入電壓:2.05 V ~ 6 V PWM 型:電壓模式 頻率 - 開關:2MHz 電流 - 輸出:500mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-UFDFN 包裝:帶卷 (TR) 供應商設備封裝:6-SON（1.45x1） 產品目錄頁面:1032 (CN2011-ZH PDF) 其它名稱:296-25628-2 |
| LT3957AEUHE#TRPBF | 功能描述:IC REG MULTI CONFIG ADJ 5A 36QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V，1.5V，1.8V，2.5V 輸入電壓:2.7 V ~ 20 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:50mA 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬）裸露焊盤 包裝:帶卷 (TR) 供應商設備封裝:10-MSOP 裸露焊盤 |
| LT3957AIUHE#PBF | 功能描述:IC REG MULTI CONFIG ADJ 5A 36QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:250 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V 輸入電壓:2.05 V ~ 6 V PWM 型:電壓模式 頻率 - 開關:2MHz 電流 - 輸出:500mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-UFDFN 包裝:帶卷 (TR) 供應商設備封裝:6-SON（1.45x1） 產品目錄頁面:1032 (CN2011-ZH PDF) 其它名稱:296-25628-2 |
發布緊急采購，3分鐘左右您將得到回復。